 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Mercury (R) Programmable Logic Device Family Data Sheet January 2003, ver. 2.2 Features... High-performance programmable logic device (PLD) family (see Table 1) - Integrated high-speed transceivers with support for clock data recovery (CDR) at up to 1.25 gigabits per second (Gbps) - Look-up table (LUT)-based architecture optimized for high speed - Advanced interconnect structure for fast routing of critical paths - Enhanced I/O structure for versatile standards and interface support - Up to 14,400 logic elements (LEs) System-level features - Up to four general-purpose phase-locked loops (PLLs) with programmable multiplication and delay shifting - Up to 12 PLL output ports - Dedicated multiplier circuitry for high-speed implementation of signed or unsigned multiplication up to 16 x 16 - Embedded system blocks (ESBs) used to implement memory functions including quad-port RAM, true dual-port RAM, firstin first-out (FIFO) buffers, and content-addressable memory (CAM) - Each ESB contains 4,096 bits and can be split and used as two 2,048-bit unidirectional dual-port RAM blocks 13 Tools Table 1. Mercury Device Features Feature Typical gates HSDI channels LEs ESBs (1) Maximum RAM bits Maximum user I/O pins Note to Table 1: (1) Each ESB can be used for two dual- or single-port RAM blocks. EP1M120 120,000 8 4,800 12 49,152 303 EP1M350 350,000 18 14,400 28 114,688 486 Altera Corporation DS-MERCURY-2.2 1 Mercury Programmable Logic Device Family Data Sheet ...and More Features Advanced high-speed I/O features - Robust I/O standard support, including LVTTL, PCI up to 66 MHz, 3.3-V AGP in 1x and 2x modes, 3.3-V SSTL-3 and 2.5-V SSTL-2, GTL+, HSTL, CTT, LVDS, LVPECL, and 3.3-V PCML - High-speed differential interface (HSDI) with dedicated circuitry for CDR at up to 1.25 Gbps for LVDS, LVPECL, and 3.3-V PCML - Support for source-synchronous True-LVDSTM circuitry up to 840 megabits per second (Mbps) for LVDS, LVPECL, and 3.3-V PCML - Up to 18 input and 18 output dedicated differential channels of high-speed LVDS, LVPECL, or 3.3-V PCML - Built-in 100- termination resistor on HSDI data and clock differential pairs - Flexible-LVDSTM circuitry provides 624-Mbps support on up to 100 channels with the EP1M350 device - Versatile three-register I/O element (IOE) supporting double data rate I/O (DDRIO), double data-rate (DDR) SDRAM, zero bus turnaround (ZBT) SRAM, and quad data rate (QDR) SRAM Designed for low-power operation - 1.8-V internal supply voltage (VCCINT) - MultiVoltTM I/O interface voltage levels (VCCIO) compatible with 1.5-V, 1.8-V, 2.5-V, and 3.3-V devices - 5.0-V tolerant with external resistor Advanced interconnect structure - Multi-level FastTrack(R) Interconnect structure providing fast, predictable interconnect delays - Optimized high-speed Priority FastTrack Interconnect for routing critical paths in a design - Dedicated carry chain that implements arithmetic functions such as fast adders, counters, and comparators (automatically used by software tools and megafunctions) - FastLUTTM connection allowing high speed direct connection between LEs in the same logic array block (LAB) - Leap lines allowing a single LAB to directly drive LEs in adjacent rows - The RapidLAB interconnect providing a high-speed connection to a 10-LAB-wide region - Dedicated clock and control signal resources, including four dedicated clocks, six dedicated fast global signals, and additional row-global signals 2 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Tables 2 and 3 show the MercuryTM FineLine BGATM device package sizes, options, and I/O pin counts. Table 2. Mercury Package Sizes Feature Pitch (mm) Area (mm2) Length x width (mm x mm) 484-Pin FineLine BGA 1.00 529 23 x 23 780-Pin FineLine BGA 1.00 841 29 x 29 Table 3. Mercury Package Options & I/O Count Device EP1M120 EP1M350 484-Pin FineLine BGA 303 780-Pin FineLine BGA 486 13 Tools General Description Mercury devices integrate high-speed differential transceivers and support for CDR with a speed-optimized PLD architecture. These transceivers are implemented through the dedicated serializer, deserializer, and clock recovery circuitry in the HSDI and incorporate support for the LVDS, LVPECL, and 3.3-V PCML I/O standards. This circuitry, together with enhanced I/O elements (IOEs) and support for numerous I/O standards, allows Mercury devices to meet high-speed interface requirements. Mercury devices are the first PLDs optimized for core performance. These LUT-based, enhanced memory devices use a network of fast routing resources to achieve optimal performance. These resources are ideal for data-path, register-intensive, mathematical, digital signal processing (DSP), or communications designs. Altera Corporation 3 Mercury Programmable Logic Device Family Data Sheet Mercury devices include other features for performance such as quadport RAM, CAM, general purpose PLLs, and dedicated circuitry for implementing multiplier circuits. Table 4 shows Mercury performance. Table 4. Mercury Performance Application Resources Used LEs 16-bit loadable counter (1) 32-bit loadable counter (1) 32-bit accumulator (1) 32-to-1 multiplexer 32 x 64 asynchronous FIFO 8-bit, 37-tap FIR filter Note to Table 4: (1) The clock tree supports up to 400 MHz. Although the registered performance for these designs exceed 400 MHz, they are limited by the clock tree limit. Performance -5 Speed Grade 400 400 400 1.864 290 290 ESBs 0 0 0 0 2 1 -6 Speed Grade 400 400 400 2.466 258 240 -7 Speed Grade 400 400 400 2.723 242 205 Units MHz MHz MHz ns MHz MSPS 16 32 32 27 103 251 Configuration The logic, circuitry, and interconnects in the Mercury architecture are configured with CMOS SRAM elements. Mercury devices are reconfigurable and are 100% tested prior to shipment. As a result, test vectors do not have to be generated for fault coverage purposes. Instead, the designer can focus on simulation and design verification. In addition, the designer does not need to manage inventories of different ASIC designs; Mercury devices can be configured on the board for the specific functionality required. Mercury devices are configured at system power-up with data stored in an Altera(R) serial configuration device or provided by a system controller. Altera offers in-system programmability (ISP)-capable configuration devices, which configure Mercury devices via a serial data stream. Mercury devices can be configured in under 70 ms. Moreover, Mercury devices contain an optimized interface that permits microprocessors to configure Mercury devices serially or in parallel, synchronously or asynchronously. This interface also enables microprocessors to treat Mercury devices as memory and to configure the device by writing to a virtual memory location, simplifying reconfiguration. 4 Altera Corporation Mercury Programmable Logic Device Family Data Sheet After a Mercury device has been configured, it can be reconfigured in-circuit by resetting the device and loading new data. Real-time changes can be made during system operation, enabling innovative reconfigurable computing applications. Software Mercury devices are supported by the Altera QuartusTM II development system, a single, integrated package that offers HDL and schematic design entry, compilation and logic synthesis, full simulation and worst-case timing analysis, SignalTapTM logic analysis, and device configuration. The Quartus II software also ships with Altera-specific HDL synthesis tools from Exemplar Logic and Synopsys, and Altera-specific Register Transfer Level (RTL) and timing simulation tools from Model Technology. The Quartus II software supports PCs running Windows 98, Windows NT 4.0, and Windows 2000; UNIX workstations running Solaris 2.6, 7, or 8, or HP-UX 10.2 or 11.0; and PCs running Red Hat Linux 7.1. The Quartus II software provides NativeLinkTM interfaces to other industry-standard PC- and UNIX-workstation-based EDA tools. For example, designers can invoke the Quartus II software from within the Mentor Graphics LeonardoSpectrum software, Synplicity's Synplify software, and the Synopsys FPGA Express software. The Quartus II software also contains built-in optimized synthesis libraries; synthesis tools can use these libraries to optimize designs for Mercury devices. For example, the Synopsys Design Compiler library, supplied with the Quartus II development system, includes DesignWare functions optimized for the Mercury architecture. For more information on the Quartus II development system, see the Quartus II Programmable Logic Development System & Software Data Sheet. 13 Tools Functional Description The Mercury architecture contains a row-based logic array to implement general logic and a row-based embedded system array to implement memory and specialized logic functions. Signal interconnections within Mercury devices are provided by a series of row and column interconnects with varying lengths and speeds. The priority FastTrack Interconnect structure is faster than other interconnects; the Quartus II Compiler places design-critical paths on these faster lines to improve design performance. Altera Corporation 5 Mercury Programmable Logic Device Family Data Sheet Mercury device I/O pins are evenly distributed across the entire device area; other Altera device families have I/O pins placed on the device periphery. Mercury device I/O pin placement allows for higher I/O count at a given die size; pad size is no longer a limiting issue. Each I/O pin is fed by an IOE. IOEs are grouped in IOE row bands from the top to the bottom of the device. IOE row bands are separated by several LAB rows. LABs from the associated LAB row closest to the I/O row band drive IOEs through the local interconnect. This feature allows fast clock-to-output times when a pin is driven by any of the 10 LEs in the adjacent associated LAB. Each IOE contains a bidirectional buffer along with an input register, output register, output enable (OE) register, and input latch for DDR. When used with a global clock, these dedicated registers provide exceptional bidirectional I/O performance. IOEs provide a variety of features, such as 3.3-V, 64-bit, 66-MHz PCI compliance; 3.3-V, 64-bit, 133-MHz PCI-X compliance; Joint Test Action Group (JTAG) boundary-scan test (BST) support; output drive strength control; slew-rate control; tri-state buffers; bus-hold circuitry; programmable pull-up resisters; programmable input and output delays; and open-drain outputs. Mercury devices offer enhanced I/O support, including support for 1.8-V I/O, 2.5-V I/O, LVCMOS, LVTTL, HSTL, LVPECL, 3.3-V PCML, 3.3-V PCI, PCI-X, LVDS, GTL+, SSTL-2, SSTL-3, CTT, and 3.3-V AGP I/O standards. CDR (up to 1.25 Gbps) and sourcesynchronous (up to 840 Mbps) transfers are supported with HSDI circuitry for LVDS, LVPECL, and 3.3-V PCML I/O standards. The ESB can implement a variety of memory functions, including CAM, quad-port RAM, true dual-port RAM, dual- and single-port RAM, ROM, and FIFO functions. ESBs are grouped into two rows: one at the top and one at the bottom of the device. Embedding the memory directly into the die improves performance and reduces die area compared to distributedRAM implementations. Moreover, the abundance of cascadable ESBs, in conjunction with the ability for one ESB to implement two separate memory blocks, ensures that the Mercury device can implement multiple wide memory blocks for high-density designs. The ESB's high speed ensures the implemention of small memory blocks without any speed penalty. The abundance of ESBs ensures that designers can create as many different-sized memory blocks as the system requires. Figure 1 shows an overview of the Mercury device. 6 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Figure 1. Mercury Architecture Block Diagram ESB Note (1) ESB ESB ESB ESB ESB Local Interconnect: Connects LEs within the Same or Adjacent LABs Row and Priority Row Interconnect: Connects LABs within a Row Column and Priority Column Interconnect: Connects LABs within Different Rows (Top to Bottom) Leap Lines: Connects Adjacent LABs in Same Column I/O Band with HSDI Associated LAB Row Buried LAB Row Buried LAB Row I/O Band Associated LAB Row Buried LAB Row Buried LAB Row I/O Band Associated LAB Row Buried LAB Row Buried LAB Row I/O Band Associated LAB Row Buried LAB Row RapidLAB Interconnect: Connects Any 10 Consecutive LABs within a Row from a Central LAB Associated LAB Row I/O Band ESB ESB ESB ESB ESB ESB 13 Tools Note to Figure 1: (1) Figure 1 shows an EP1M120 device. Mercury devices have a varying number of rows, columns, and ESBs, as shown in Table 5. Table 5 lists the resources available in Mercury devices. Table 5. Mercury Device Resources Device EP1M120 EP1M350 LAB Rows 12 18 LAB Columns 40 80 I/O Row Bands 5 4 ESBs 12 28 Altera Corporation 7 Mercury Programmable Logic Device Family Data Sheet Mercury devices provide four dedicated clock input pins and six dedicated fast I/O pins that globally drive register control inputs, including clocks. These signals ensure efficient distribution of high-speed, low-skew control signals. The control signals use dedicated routing channels to provide short delays and low skew. The dedicated fast signals can also be driven by internal logic, providing an ideal solution for a clock divider or internally generated asynchronous control signal with high fan-out. The dedicated clock and fast I/O pins on Mercury devices can also feed logic. Dedicated clocks can also be used with the Mercury general purpose PLLs for clock management. Each I/O row band also provides two additional I/O pins that can drive two row-global signals. Row-global signals can drive register control inputs for the LAB row associated with that particular I/O row band. High-Speed Differential Interface The top I/O or HSDI band in Mercury devices contains dedicated circuitry for supporting differential standards at speeds up to 1.25 Gbps. Mercury devices have dedicated differential buffers and circuitry to support LVDS, LVPECL, and 3.3-V PCML I/O standards. Two dedicated high-speed PLLs (separate from the general purpose PLLs) multiply reference clocks and drive high-speed differential serializer/deserializer channels. In addition, clock recovery units (CRUs) at each receiver channel enable CDR. EP1M120 devices support eight input channels, eight output channels, and two dedicated clock inputs for feeding the receiver and/or transmitter PLLs. EP1M350 devices support 18 input channels, 18 output channels, and two dedicated clock inputs. Mercury devices have optional built-in 100- termination resistors on HSDI differential receiver data pins and the HSDI_CLK1 and HSDI_CLK2 pins. Designers can use the HSDI circuitry for the following applications: Gigabit Ethernet backplanes ATM, SONET RapidIO POS-PHY Level 4 Fibre Channel SDTV The HSDI band supports one of two possible modes: Source-synchronous mode Clock data recovery (CDR) mode 8 Altera Corporation Mercury Programmable Logic Device Family Data Sheet In source-synchronous mode, source synchronous interfacing is supported at up to 840 Mbps. Serial channels are transmitted and received along with a low speed clock. The receiving device then multiplies the clock by a factor of 1 to 12, 14, 16, 18, or 20. The serialization/ deserialization rate can be any number from 4, 7, 8, 9 to 12, 14, 16, 18, or 20 and does not have to equal the clock multiplication value. For example, an 840-Mbps LVDS channel can be received along with a 84-MHz clock. The 84-MHz clock is multiplied by 10 to drive the serial shift register, but the register can be clocked out in parallel at 7-, 8-, 9- to 12-, 14-, 16-, 18-, or 20-bits wide at 42 to 120 MHz. See Figures 2 and 3. Figure 2. Receiver Diagram for Source Synchronous Mode Notes (1), (2) J Bits Wide Deserializer Data to LEs Receiver Channel + -- HSDI_CLK2 (3) HSDI xW PLL2 1 J To Global Clock Receiver Channel 1 13 Tools Receiver Channel + -- Receiver Channel 2 Receiver Channel + -- Receiver Channel 8 Notes to Figure 2: (1) (2) EP1M350 devices have 18 individual receiver channels. EP1M120 devices have 8 individual receiver channels. W = 1 to 12, 14, 16, 18, or 20 J = 4, 7, 8, 9 to 12, 14, 16, 18, or 20 W does not have to equal J. This clock pin drives an HSDI PLL only. It does not drive to the core. (3) Altera Corporation 9 Mercury Programmable Logic Device Family Data Sheet Figure 3. Transmitter Diagram for Source Synchronous Mode Notes (1), (2) J Bits Wide Serializer Data from LEs Transmitter Channel Global Clock from Receiver or System Clock HSDI_CLK1 (3) HSDI PLL1 xW xW B 1 J Transmitter Channel 1 TXOUTCLOCK Transmitter Channel Transmitter Channel 2 Transmitter Channel Transmitter Channel 8 Notes to Figure 3: (1) (2) EP1M350 devices have 18 individual transmitter channels. EP1M120 devices have 8 individual transmitter channels. W = 1 to 12, 14, 16, 18, or 20 B = 1 to 12, 14, 16, 18, or 20 J = 4, 7, 8, 9 to 12, 14, 16, 18, or 20 W, B, and J do not have to be equal. This clock pin drives an HSDI PLL only. It does not drive to the logic array. (3) The Mercury device's source-synchronous mode also supports the RapidIO interface protocol at up to 500 Mbps using the LVDS I/O standard. f For more information on source synchronous interfacing see AN 159: Using HSDI in Source-Synchronous Mode in Mercury Devices. 10 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Table 6 defines the support for source-synchronous mode applications. Table 6. Source-Synchronous Mode Data Rate LVDS 840 Mbps Note to Table 6: (1) You can use the CDR circuit to achieve data rates for DC coupled LVDS applications. You must AC-couple the clock to a 2.2-V common mode voltage (VCM) using the AC-coupling schemes in AN 134: Using Programmable I/O Standards in Mercury Devices. The data channels should be DC-coupled. The byte alignment relative to the clock is lost when using the CDR circuit. Therefore, a byte-alignment circuit is required. Most Mercury source-synchronous designs already include byte-alignment logic since they usually use DDR or SDR clocks. The CDR run length requirement is waived if the reference clock and the receiver data come from the same source and have the same frequency. I/O Standard LVPECL v 3.3-V PCML v (1) In CDR mode, serial data is supported up to 1.25 Gbps per channel. The system provides a reference clock which is multiplied by the receiver or transmitter PLL to the same rate as the data is provided. For the receiver, this multiplied reference clock is used by a CRU on each receiver channel to generate a recovered clock in-phase with the received data. That recovered clock drives the programmable deserializer and synchronizer. The synchronizer is a FIFO for data transfer between the recovered clock domain and the global clock domain. The dedicated synchronizers can be bypassed if necessary. For every receiver channel in the EP1M350 and EP1M120 devices, the /J recovered clock can drive a priority column line for use as a clock. See Figure 4. 13 Tools Altera Corporation 11 12 4 Dedicated Clocks (3) Data Data Data Data Data GCLK4 GCLK3 GCLK2 GCLK1 (3) J J J J J Data (3) (3) Data Data J J J Synchronizer Synchronizer Synchronizer Synchronizer Synchronizer Synchronizer Synchronizer Synchronizer (4) Serializer Serializer Deserializer (4) (4) (4) Deserializer Serializer Deserializer Figure 4. Receiver & Transmitter Diagrams for CDR Mode Mercury Programmable Logic Device Family Data Sheet Serializer Deserializer /J REFCLK PLL1 RCLK DPLL 8 8 xW xW /J REFCLK PLL2 /J /J /J /J /J /J RCLK RCLK DPLL RCLK DPLL Notes (1), (2) DPLL +-- +-- HSDI_CLK1 (5) TX4 (TX9) RX4 (RX9) +-- +-- TX5 (TX10) HSDI_CLK2 (5) +-- RX5 (RX10) TX6 (TX11) +-- RX6 (RX11) TX3 (TX8) RX3 (RX8) Altera Corporation Mercury Programmable Logic Device Family Data Sheet Notes to Figure 4: (1) EP1M350 devices have 18 individual receiver and transmitter channels. EP1M120 devices have 8 individual receiver and transmitter channels. Receiver and transmitter channel numbers in parenthesis are for EP1M350 devices. W = 1 to 12, 14, 16, 18, or 20 J = 3 to 12, 14, 16, 18, or 20 W does not have to equal J. For every receiver channel in EP1M350 and EP1M120 devices, the /J recovered clock can drive the priority column interconnect for use as a clock. The two center channels adjacent to the HSDI PLLs (channels 4 and 5 for EP1M120 devices, channels 9 and 10 for EP1M350 devices) can drive the Mercury device's global clocks. HSDI_CLK1 and HSDI_CLK2 pins must be differential. These clock pins drive HSDI PLLs only. They do not drive to the logic array. (2) (3) (4) (5) The multiplied reference clock is also used to synchronize and serialize at the transmitter side. Up to two different serial data rates are supported for input channels or output channels. Received data must be non-return-to-zero (NRZ). Table 7 defines the support for CDR-mode applications. Table 8 shows the supported data rates for each speed grade. Table 7. CDR-Mode Applications Data Rate CDR Mode DC-Coupled DC-Coupled DC-Coupled AC-Coupled AC-Coupled AC-Coupled LVDS LVPECL 3.3-V PCML LVDS (1) LVPECL (1) 3.3-V PCML (1) 1.0 to 1.25 Gbps 1.0 Gbps Notes to Table 7: (1) (2) The VCM operating range for AC-coupled applications is from 0 to 0.7 V and from 1.8 to 2.4 V. Use AC-coupled LVDS or another I/O standard. The DC-coupled LVDS I/O standard provides performance up to 1.0 Gbps. 13 Tools (2) v v v v v v v v v v v f For more information on CDR, see AN 130: CDR in Mercury Devices. Altera Corporation 13 Mercury Programmable Logic Device Family Data Sheet 1 Mercury device HSDI performance is finalized for certain speed grades. Also, the industrial-grade CDR specification is the same as the -6 speed grade for commercial-grade CDR specification. See Table 8. Table 8. CDR & Source-Synchronous Data Rates Device Speed Grade Number of Channels Maximum CDR Data Rate (Gbps) 1.25 1.25 1.0 1.25 1.25 1.0 1.0 Maximum SourceSynchronous Data Rate (Mbps) 840 840 840 840 840 840 840 EP1M120 -5 -6 (1) -7 8 8 8 18 8 (2) 10 (2) 18 EP1M350 -5 -6 (1) -7 Notes to Table 8: (1) (2) The -6 speed grade specifications apply for both commercial and industrial devices. EP1M350 devices can support any 8 channels at 1.25 Gbps. The other 10 channels must run at 1.0 Gbps or less. Logic & Interconnect Mercury device logic is implemented in LEs. LE resources are used differently according to specific operating modes and the type of logic function being implemented. LEs are grouped into LABs in a row-based architecture. The multi-level FastTrack Interconnect structure provides the routing connection between LEs, ESBs, and IOEs. Logic Array Block Each LAB consists of 10 LEs, LE carry chains, multiplier circuitry, LAB control signals, local interconnect, and FastLUT connection lines. The local interconnect transfers signals between LEs within the same or adjacent LABs. FastLUT connections transfer the output of one LE to the adjacent LE for ultra-fast sequential LE connections within the same LAB. The Quartus II Compiler places associated logic within a LAB or adjacent LABs, allowing the use of fast local and FastLUT connections for high performance. Figure 5 shows the Mercury LAB structure. 14 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Figure 5. Mercury LAB Structure Row and Priority Row Interconnect (1) to LAB in Row Above (2) (3) RapidLAB Interconnect (3) Column and Priority Column Interconnect (1) 13 Tools Local Interconnect Leap Line Interconnect The 10 LEs in the LAB are driven by two local interconnect areas. The LAB can drive two local interconnect areas. to LAB in Row Below Notes to Figure 5: (1) (2) (3) Priority column lines drive priority row lines, but not other row lines. The RapidLAB interconnect can be driven by priority column lines, but not other column lines. In multiplier mode, the RapidLAB interconnect drives LEs directly. Mercury devices use an interleaved LAB structure, which allows each LAB to drive two local interconnect areas. Every other LE drives to either the left or right local interconnect area, alternating by LE. The local interconnect can drive LEs within the same LAB or adjacent LABs. This feature minimizes use of the row and column interconnects, providing higher performance and flexibility. Each LAB structure can drive 30 LEs through fast local interconnects. Altera Corporation 15 Mercury Programmable Logic Device Family Data Sheet Each LAB contains dedicated logic for driving control signals to its LEs. The control signals include clock, clock enable, asynchronous clear, asynchronous preset, asynchronous load, synchronous clear, and synchronous load signals. A maximum of six control signals can be used at a time. Although synchronous load and clear signals are generally used when implementing counters, they can also be used with other functions. Each LAB can use two clocks and two clock enable signals. Each LAB's clock and clock enable signals are linked (e.g., any LE in a particular LAB using LABCLK1 will also use LABCLKENA1). In addition to LAB-wide control of clock enables, Mercury devices can also control clock enable signals on individual LEs, allowing more than two clock enables in a given LAB. The Quartus II software automatically chooses whether a clock enable is LAB-wide for individual LEs. If both the rising and falling edges of a clock are used in a LAB, both LAB-wide clock signals are used. The LAB local interconnect, fast global signals, row-global signals, and dedicated clock pins can generate the LAB-wide control signals. The multi-level FastTrack Interconnect's inherent low skew allows it to be used for clock distribution. Figure 6 shows the LAB control signal generation circuit. 16 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Figure 6. LAB-Wide Control Signals Dedicated Clocks Fast Global Signals Row Global Signals 4 6 2 Local Interconnect Local Interconnect Local Interconnect Local Interconnect ASYNCLOAD or LABPRE SYNCCLR or LABCLK2 SYNCLOAD or LABCLKENA2 LABCLKENA1 13 Tools LABCLK1 LABCLR Logic Element The LE, the smallest unit of logic in the Mercury architecture, is compact and provides efficient logic usage. Each LE contains a four-input LUT, which is a function generator that can quickly implement any function of four variables. In addition, each LE contains a programmable register and carry chain with carry select look ahead capability. Each LE drives all interconnect types: local interconnect, row and priority row interconnect, column and priority column interconnect, leap lines, and RapidLAB interconnect. Each LE also has the ability to drive its combinatorial output directly to the next LE in the LAB using FastLUT connections. See Figure 7. Altera Corporation 17 Mercury Programmable Logic Device Family Data Sheet Figure 7. Mercury LE LAB Carry-In Carry-In1 Carry-In0 LAB-wide Synchronous Load Register Bypass Packed Register Select Programmable Register LAB-wide Synchronous Clear FastLUT Routing to next LE to Local, Row, and Column Routing data1 data2 data3 data4 (1) Look-Up Table (LUT) Carry Chain Synchronous Load and Clear Logic D PRN Q ENA CLRN to Local, Row, and Column Routing labclr labpre Chip-Wide Reset Asynchronous Clear/Preset/ Load Logic Clock & Clock Enable Select labclk1 labclk2 labclkena1 labclkena2 Carry-Out0 Carry-Out1 LE Clock Enable LAB Carry-Out (2) Notes to Figure 7: (1) (2) FastLUT interconnect uses the data4 input. LAB carry-out can only be generated by LE 4 and/or LE 10. Each LE's programmable register can be configured for D, T, JK, or SR operation. The register's clock, clock enable, and clear control signals can be driven by global signals, general-purpose I/O pins, or any internal logic. For combinatorial functions, the register is bypassed and the output of the LUT drives directly to the outputs of the LE. Each LE has four data inputs that can drive the internal LUT. One of these inputs has a shorter delay than the others, improving overall LE performance. This input is chosen automatically by the Quartus II software as appropriate. 18 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Each LE has two outputs that drive the local, row, and column routing resources. Each output can be driven independently by the LUT's or register's output. For example, the LUT can drive one output, while the register drives the other output. This feature, called register packing, improves device utilization because the register and the LUT can be used for unrelated functions. The LE can also drive out registered and unregistered versions of the LUT output. LE Operating Modes The Mercury LE can operate in one of the following modes: Normal Arithmetic Multiplier Each operating mode uses LE resources differently. In each operating mode, eight available inputs to the LE--the four data inputs from the LAB local interconnect; carry-in0, carry-in1 from the previous LE; the LAB carry-in from the previous carry-chain generation; and the FastLUT Connection input from the previous LE--are directed to different destinations to implement the desired logic function. LAB-wide signals provide clock, asynchronous clear, asynchronous preset, asynchronous load, synchronous clear, synchronous load, and clock enable control for the register. These LAB-wide signals are available in all normal and arithmetic LE modes. The Quartus II software, in conjunction with parameterized functions such as LPM and DesignWare functions, automatically chooses the appropriate mode for common functions, such as counters, adders, and multipliers. If required, the designer can also create special-purpose functions that specify which LE operating mode to use for optimal performance. Normal Mode The normal mode is suitable for general logic applications and combinatorial functions. In normal mode, four data inputs from the LAB local interconnect and a single carry-in are inputs to a four-input LUT. The Quartus II Compiler automatically selects the carry-in or the data3 signal as one of the inputs to the LUT. The LUT (combinatorial) output can be driven to the FastLUT connection to the next LE in the LAB. LEs in normal mode support packed registers. Figure 8 shows an LE in normal mode. 13 Tools Altera Corporation 19 Mercury Programmable Logic Device Family Data Sheet Figure 8. Normal-Mode LE Note (1) LE-Out Combinatorial Output data1 data2 data3 Carry-In from Previous LE (2) data4 LE-Out 4-Input LUT PRN/ALDn Output D Q ENA CLRN Registered LE-Out LAB-Wide Clock Enable (3) Notes to Figure 8: (1) (2) (3) LEs in normal mode support register packing. When using the carry-in in normal mode, the packed register feature is unavailable. There are two LAB-wide clock enables per LAB in addition to LE-specific clock enables. Arithmetic Mode The arithmetic mode is ideal for implementing adders, accumulators, and comparators. A LE in arithmetic mode contains four 2-input LUTs. The first two 2-input LUTs compute two summations based on a possible carry of 1 or 0; the other two LUTs generate carry outputs for the two possible chains of the carry-select look-ahead (CSLA) circuitry. As shown in Figure 9, the LAB carry-in signal selects the appropriate carry-in chain (either carry-in0 or carry-in1). The logic level of the chain selected in turn selects which parallel sum is generated as a combinatorial or registered output. For example, when implementing an adder, this output is the signal comprised of the sum data1 + data2 + carry, where carry is 0 or 1. The other two LUTs use the data1 and data2 signals to generate two possible carry-out signals--one for a carry of 1 and the other for a carry of 0. The carry-in0 signal acts as the carry select for the carry-out0 output; carry-in1 acts as the carry select for the carry-out1 output. LEs in arithmetic mode can drive out registered and unregistered versions of the LUT output. Figure 9 shows a Mercury LE in arithmetic mode. 20 Altera Corporation Mercury Programmable Logic Device Family Data Sheet The arithmetic mode also offers clock enable, counter enable, synchronous up/down control, synchronous clear, and synchronous load options. The counter enable and synchronous up/down control signals are generated from the data inputs of the LAB local interconnect. The synchronous clear and synchronous load options are LAB-wide signals that affect all registers in the LAB. Consequently, if any of the LEs in a LAB use the counter mode, other LEs in that LAB must be used as part of the same counter or be used for a combinatorial function. The Quartus II software automatically places any registers that are not used by the counter into other LABs. Figure 9. Arithmetic Mode LE LAB Carry-In Carry-In0 Carry-In1 data1 data2 LUT LAB-Wide Synchronous Clear LAB-Wide Synchronous Load Sum LUT Registered PRN/ALDn Output Q Combinatorial Output LE-Out D 13 LE-Out LUT ENA CLRn Tools LUT data3 LAB-Wide Clock Enable Carry-Out0 Carry-Out1 Carry-Select Look-Ahead Chain The CSLA chain provides a very fast carry-forward function between LEs in arithmetic mode or multiplier mode. The CSLA chain uses the redundant carry calculation to increase the speed of carry functions. The LE can calculate sum and carry values for a possible carry-in of 1 and carry-in of 0 in parallel. The carry-in0 and carry-in1 signals from a lower-order bit drive forward into the higher-order bit via the parallel carry chain and feed into both the LUT and the next portion of the CSLA chain. CSLA chains can begin in any LE within a LAB. Altera Corporation 21 Mercury Programmable Logic Device Family Data Sheet The CSLA chain's speed advantage results from the parallel precomputation of carry chains. Instead of including every LUT in the critical path, only the propagation delays between LAB carry-in generation circuits (LE 4 and LE 10) make up the critical path. This feature allows the Mercury architecture to implement high-speed counters, adders, multipliers, parity functions, and comparators of arbitrary width. Figure 10 shows the CSLA circuitry in a LAB for a 10-bit full adder. One portion of the LUT generates the sum of two bits using the input signals and the appropriate carry-in bit; the sum is routed to the output of the LE. The register can be bypassed for simple adders or used for accumulator functions. Another portion of the LUT generates carry-out bits. A labwide carry-in bit selects which chain is used for the addition of given inputs. The actual carry-in signal for that selected chain, carry-in0 or carry-in1, selects the carry-out to carry forward, which is routed to the carry-in signal of the next-higher-order bit. The final carry-out signal is routed to an LE, where it is driven to local, row, or column interconnects. 22 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Figure 10. CSLA Details LAB Carry-In A1 B1 A2 B2 A3 B3 A4 B4 0 LE1 1 Sum1 LAB Carry-In Carry-In0 Carry-In1 LE2 Sum2 LUT data1 data2 Sum LUT LE3 Sum3 LE4 Sum4 LUT LUT 0 A5 B5 A6 B6 A7 B7 A8 B8 A9 B9 A10 B10 LE5 1 Sum5 LE6 Sum6 Carry-Out0 Carry-Out1 13 Tools LE7 Sum7 LE8 Sum8 LE9 Sum9 LE10 Sum10 LAB Carry-Out The Quartus II Compiler can create CSLA logic automatically during design processing. Alternatively, the designer can create CSLA logic manually during design entry. Parameterized functions such as library of parameterized modules (LPM) and DesignWare functions automatically take advantage of carry chains for the appropriate functions. Altera Corporation 23 Mercury Programmable Logic Device Family Data Sheet The Quartus II Compiler creates carry chains longer than ten LEs by linking LABs together automatically. For enhanced fitting, a long carry chain skips intermediate LABs in a row structure. A carry chain longer than one LAB skips either from an even-numbered LAB to the next evennumbered LAB, or from an odd-numbered LAB to the next oddnumbered LAB. For example, the last LE of the first LAB in a LAB row carries to the first LE of the third LAB in the same LAB row. Multiplier Mode Multiplier mode is used for implementing high-speed multipliers up to 16 x 16 in size. The LUT implements the partial product formation and summation in a single stage for a N x M-bit multiply operation. A single LE can implement the summation of ANBM + 1 + AN + 1BM for the multiplier and multiplicand inputs. To increase the speed of the multiplication, LAB wide signals are used to control the partial product sum generation. These multiplier LAB-wide signals use the LABCLKENA1 and PRESET/ASYNCLOAD resources. The multiplier mode takes advantage of the CSLA circuitry for optimized sum and carry generation in the partial product sum. There is a special CSLA circuitry mode used for the multiplier where the carry chain runs vertically between LABs in the same column. The Quartus II Compiler automatically uses this special mode for dedicated multiplier implementation only. The summation of the multiplier and multiplicand bits is driven out along with the carryout0 and carry-out1 bits. The combinatorial or registered versions of the sum can be driven out, allowing the multiplier to be pipelined. The RapidLAB interconnect has dedicated fast connections to the LE inputs in multiplier mode, further increasing the speed of the multiplier. These dedicated connections allow RapidLAB lines to avoid delay incurred by driving onto local interconnects and then into the LE. The Quartus II software implements parameterized functions that use the multiplier mode automatically when multiply operators are used. Figure 11 shows a Mercury device LE in multiplier mode. 24 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Figure 11. Multiplier Mode LE LAB-Wide Clock Enable Signals (1) LAB Carry-In Carry-In0 Carry-In1 Combinatorial Sum Output Combinatorial Sum Output AN BM + 1 AN + 1 BM Programmable Inverter D Q RapidLAB Interconnect (2) LE Output LE Output Programmable Inverter Programmable Inverter Programmable Inverter Full Adder Registered Sum Output ENA CLRN LAB Carry-Out Carry-Out1 Partial Product Generation Carry-Out0 13 Tools Notes to Figure 11: (1) (2) LABCLKENA1 cannot be used in multiplier mode. When the RapidLAB output is used, local interconnect outputs are unavailable. The basis for the high-speed 16 x 16-bit multiplier in a Mercury device is the binary tree multiplier. In the first stage of the binary tree, the multiplicand bits, a[15:0], and the multiplier bits, b[15:0], are multiplied together. The results of the first stage are sixteen 16-bit partial products, a[15:0]b[15], a[15:0]b[14], . . . a[15:0]b[0]. The partial products are then grouped into pairs and added together in the second stage. In a similar fashion, the results of the previous stage are grouped in pairs and then added forming the binary tree structure seen in Figure 12. Altera Corporation 25 26 A15 x B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 B1 A0 B0 == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == A15B0 A14B0 A13B0 A12B0 A11B0 A10B0 A9B0 A15B1 A14B1 A13B1 A12B1 A11B1 A10B1 A9B1 A8B1 A7B2 A6B3 A5B4 A4B5 A3B6 A2B7 A1B8 A0B9 A0B8 A1B7 A0B7 A2B6 A1B6 A3B5 A2B5 A1B5 A0B6 A4B4 A3B4 A2B4 A5B3 A4B3 A3B3 A2B3 A1B4 A0B5 A6B2 A5B2 A4B2 A3B2 A2B2 A1B3 A0B4 A7B1 A6B1 A5B1 A4B1 A3B1 A15B2 A14B2 A13B2 A12B2 A11B2 A10B2 A9B2 A15B3 A14B3 A13B3 A12B3 A11B3 A10B3 A9B3 A8B3 A7B4 A6B5 A5B6 A4B7 A3B8 A2B9 A1B9 A2B8 A3B7 A4B6 A5B5 A6B4 A7B3 A15B4 A14B4 A13B4 A12B4 A11B4 A10B4 A9B4 A15B5 A14B5 A13B5 A12B5 A11B5 A10B5 A9B5 A8B5 A7B6 A6B7 A5B8 A4B9 A3B9 A4B8 A5B7 A6B6 A7B5 A15B6 A14B6 A13B6 A12B6 A11B6 A10B6 A9B6 A8B6 A7B7 A6B8 A5B9 A15B7 A14B7 A13B7 A12B7 A11B7 A10B7 A9B7 A8B7 A7B8 A6B9 A8B8 A7B9 A8B4 A8B2 A8B0 A7B0 A6B0 A5B0 A4B0 A3B0 A2B1 A1B2 A0B3 A2B0 A1B1 A0B2 A1B0 A0B1 A0B0 Figure 12. Partial Product Formation Sixteen 16-Bit Partial Products Mercury Programmable Logic Device Family Data Sheet A15B8 A14B8 A13B8 A12B8 A11B8 A10B8 A9B8 A8B9 A15B9 A14B9 A13B9 A12B9 A11B9 A10B9 A9B9 A15B10 A14B10 A13B10 A12B10 A11B10 A10B10 A9B10 A8B10 A7B10 A6B10 A5B10 A4B10 A3B10 A2B10 A1B10 A0B10 A15B11 A14B11 A13B11 A12B11 A11B11 A10B11 A9B11 A8B11 A7B11 A6B11 A5B11 A4B11 A3B11 A2B11 A1B11 A0B11 A15B12 A14B12 A13B12 A12B12 A11B12 A10B12 A9B12 A8B12 A7B12 A6B12 A5B12 A4B12 A3B12 A2B12 A1B12 A0B12 A15B13 A14B13 A13B13 A12B13 A11B13 A10B13 A9B13 A8B13 A7B13 A6B13 A5B13 A4B13 A3B13 A2B13 A1B13 A0B13 A15B14 A14B14 A13B14 A12B14 A11B14 A10B14 A9B14 A8B14 A7B14 A6B14 A5B14 A4B14 A3B14 A2B14 A1B14 A0B14 A15B15 A14B15 A13B15 A12B15 A11B15 A10B15 A9B15 A8B15 A7B15 A6B15 A5B15 A4B15 A3B15 A2B15 A1B15 A0B15 == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == == Altera Corporation Mercury Programmable Logic Device Family Data Sheet For a typical 16 x 16-bit binary tree multiplier, five stages are needed to determine the final product. The Mercury LE multiplier mode allows the partial product formation stage (Stage 1) and the first sum of stages (Stage 2) to be combined in a single stage, shown in Figure 13. This feature, combined with the direct connection between RapidLAB lines and LEs in multiplier mode, allows the fast dedicated implementation of multipliers. 13 Tools Altera Corporation 27 28 A[15:0] B[12] A[15:0] B[11] A[15:0] B[10] A[15:0] B[9] A[15:0] B[8] A[15:0] B[7] A[15:0] B[6] A[15:0] B[5] A[15:0] B[4] A[15:0] B[3] A[15:0] B[2] A[15:0] B[1] A[15:0] B[0] + + + + + + + + + + + + + A[15:0] B[15] A[15:0] B[14] A[15:0] B[13] Stage 1 Figure 13. Mercury Binary Tree Implementation Stage 2 + Mercury Programmable Logic Device Family Data Sheet Stage 3 + Stage 4 Stage 5 Stages 1 and 2 are combined into one level of LEs Altera Corporation Mercury Programmable Logic Device Family Data Sheet Clear & Preset Logic Control LAB-wide signals control logic for the register's clear and preset signals. The LE directly supports an asynchronous clear and preset function. The direct asynchronous preset does not require a NOT-gate push-back technique. Mercury devices support simultaneous preset, or asynchronous load, and clear. Asynchronous clear takes precedence if both signals are asserted simultaneously. Each LAB supports one clear and one preset signal. Two clears are possible in a single LAB by using a NOT-gate push-back technique on the preset port. The Quartus II Compiler automatically performs this second clear emulation. In addition to the clear and preset ports, Mercury devices provide a chipwide reset pin (DEV_CLRn) that resets all registers in the device. Use of this pin is controlled through an option in the Quartus II software that is set before compilation. The chip-wide reset overrides all other control signals. Multi-Level FastTrack Interconnect The Mercury architecture provides connections between LEs, ESBs, and device I/O pins via an innovative Multi-Level FastTrack Interconnect structure. The Multi-Level FastTrack Interconnect structure is a series of routing channels that traverse the device, providing a hierarchy of interconnect lines. Regular resources provide efficient and capable connections while priority resources and specialized RapidLAB, leap line, and FastLUT resources enhance performance by accelerating timing on critical paths. The Quartus II Compiler automatically places critical design paths on those faster lines to improve design performance. This network of routing structures provides predictable performance, even for complex designs. In contrast, the segmented routing in FPGAs requires switch matrices to connect a variable number of routing paths, increasing the delays between logic resources and reducing performance. The Multi-Level FastTrack Interconnect consists of regular and priority lines that traverse column and row interconnect channels to span sections and the entire device length. Each row of LABs, ESBs, and I/O bands is served by a dedicated row interconnect, which routes signals to and from LABs, ESBs, and I/O row bands in the same row. These row resources include: 13 Tools Row interconnect traversing the entire device from left to right Priority row interconnect for high speed access across the length of the device RapidLAB interconnect for horizontal routing that traverses a 10-LAB-wide region from a central LAB Altera Corporation 29 Mercury Programmable Logic Device Family Data Sheet The RapidLAB interconnect provides a specialized high-speed structure to allow a central LAB to drive other LABs within a 10-LAB-wide region. The RapidLAB lines drive alternating local LAB interconnect regions, allowing communication to all LABs in the 10-LAB-wide region. Even numbered LEs in a LAB directly drive a RapidLAB line that drives one set of alternating local interconnect regions, while odd-numbered LEs drive a RapidLAB line that drives the opposite set of alternating local interconnect regions. Figure 14 shows RapidLAB interconnect connections. This 10-LAB wide region of the RapidLAB interconnect is repeated for every LAB in the row. The region covered by the RapidLAB interconnect is smaller than 10 for source LABs that are four or five LABs in from either edge of the LAB row. The RapidLAB row interconnect is used for LAB-to-LAB routing; it is only used by I/O bands or ESBs indirectly through other interconnects. The RapidLAB interconnect drives an LE directly when that LE is in multiplier mode. 30 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Figure 14. RapidLAB Interconnect Connections RapidLAB Interconnect LE 1 LE 3 LE 5 LE 7 LE 9 RapidLAB interconnects driven by odd-numbered LEs can drive out to the four LEs to the left and five LEs to the right through local interconnects. LAB Local Interconnect LE 2 LE 4 LE 6 LE 8 13 RapidLAB interconnects driven by even-numbered LEs can drive out to the four LEs to the right and five LEs to the left through local interconnects. LE 10 Tools The column interconnect vertically routes signals to and from LABs, ESBs, and I/O bands. Each column of LABs is served by a dedicated column interconnect. These column resources include: Column interconnect traversing the entire device from top to bottom Priority column interconnect for high speed access across the device vertically Leap line interconnect for vertical routing between adjacent LAB rows and between adjacent ESP rows and LAB rows. Leap lines are driven directly by LEs for fast access to adjacent row interconnects. LABs can drive a leap line to the row above and/or below (including ESB rows). The even-numbered LEs in a LAB drive leap lines down, while odd-numbered LEs drive leap lines up. This allows a single LAB to access row and RapidLAB interconnects within a three-row region. Figure 15 shows the leap line interconnect. Altera Corporation 31 Mercury Programmable Logic Device Family Data Sheet Figure 15. Leap Line Interconnect Leap Line LAB Row n-1 LE 1 LE 2 LE 3 LE 4 LE 5 LE 6 LE 7 LE 8 LE 9 LE 10 LE 1 LE 2 LE 3 LE 4 LE 5 LE 6 LE 7 LE 8 LE 9 LE 10 LE 1 LE 2 LE 3 LE 4 LE 5 LE 6 LE 7 LE 8 LE 9 LE 10 LAB Row n Priority Row and Row LAB Row n+1 RapidLAB Leap Line FastLUT Interconnect Mercury devices include an enhanced interconnect structure within LABs for faster routing of LE output to LE input connections. The FastLUT connection allows the combinatorial output of an LE to directly drive the fast input of the LE directly below it, bypassing the local interconnect. This resource can be used as a high speed connection for wide fan-in functions from LE 1 to LE 10 in the same LAB. Figure 16 shows a FastLUT interconnect. 32 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Figure 16. FastLUT Interconnect Local Interconnect Routing Among LEs in the LAB LE 1 FastLUT Routing to Adjacent LE LE 2 LE 3 LE 4 LE 5 LE 6 LE 7 LE 8 13 Tools LE 9 LE 10 ESB rows also have their own interconnect resources to communicate horizontally and vertically with LAB rows. The ESB rows at the top and bottom of the device have their own set of row and priority row interconnect resources. For vertical communication, all LAB column interconnect lines traverse to the ESBs. This includes leap lines, which allow the adjacent LAB rows to communicate with the ESBs. The row interconnect resources can be driven directly by LEs or ESBs in that row. Further, the column interconnect resources can drive a row line, allowing LEs, IOEs, and ESBs to drive elements in a different row via the column and row resources. The column interconnect resources can be directly driven by LEs, IOEs, or ESBs within that column. The priority column and leap line resources can be driven directly by LEs. These lines enable high-speed vertical communication in the device for timing-critical paths. The column resources route signals between rows. A column resource can drive row resources directly, allowing fast connections between rows. Altera Corporation 33 Mercury Programmable Logic Device Family Data Sheet Table 9 summarizes how various elements of the Mercury architecture drive each other. Table 9. Mercury Routing Scheme Source LE LE Local Interconnect IOE ESB Row ESB Interconnect Destination Row Priority RapidLAB Column Priority Leap Row Interconnect Column Lines v (1) v v v (2) v v v v v v v v v v v v v v Local v Interconnect IOE ESB Row Interconnect ESB Row Priority Row RapidLAB v Interconnect (4) Column Priority Column Leap Lines Notes to Table 9: (1) (2) (3) (4) v (3) v (3) v v v v v v v v v v v v v v v v This direct connection is possible through the FastLUT connection. IOEs can connect to the adjacent LAB's local interconnects in the associated LAB row. IOEs can connect to row and priority row interconnects in the associated LAB row. This connection is used for multiplier mode. Embedded System Block The ESB can implement various types of memory blocks, including quadport, true dual-port, dual- and single-port RAM, ROM, FIFO, and CAM blocks. The ESB includes input and output registers; the input registers synchronize reads and/or writes, and the output registers can pipeline designs to further increase system performance. The ESB offers a quad port mode, which supports up to four port operations, two reads and two writes simultaneously, with the ability for a different clock on each of the four ports. Figure 17 shows the ESB quad-port block diagram. 34 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Figure 17. ESB Quad-Port Block Diagram A dataA[ ] wraddressA[ ] wrenA inclockA inclockenA inaclrA rdaddressA[ ] rdenA qA[ ] outclockA outclockenA outaclrA B dataB[ ] wraddressB[ ] wrenB inclockB inclockenB inaclrB rdaddressB[ ] rdenB qB[ ] outclockB outclockenB outaclrB In addition to quad port memory, the ESB also supports true dual-port, dual-port, and single-port RAM. True dual-port RAM supports any combination of two port operations: two reads, two writes, or one read and one write. Dual-port memory supports a simultaneous read and write. For single-port memory, independent read and write is supported. Figure 18 shows these different RAM memory port configurations for an ESB. 13 Tools Altera Corporation 35 Mercury Programmable Logic Device Family Data Sheet Figure 18. RAM Memory Port Configurations True Dual-Port Memory A dataA[ ] addressA[ ] wrenA clockA clockenA qA[ ] aclrA B dataB[ ] addressB[ ] wrenB clockB clockenB qB[ ] aclrB Dual-Port Memory (1) data[ ] wraddress[ ] wren inclock inclocken inaclr rdaddress[ ] rden q[ ] outclock outclocken outaclr Single-Port Memory (1) data[ ] address[ ] wren inclock inclocken inaclr q[ ] outclock outclocken outaclr Note to Figure 18: (1) Two dual- or single-port memory blocks can be implemented in a single ESB. The ESB also allows variable width data ports for reading and writing to any of the RAM ports in any RAM configuration. For example, the ESB in quad port configuration can be written in x1 mode at port A, read in x16 from port A, written in x4 mode at port B, and read in x2 mode from port B. 36 Altera Corporation Mercury Programmable Logic Device Family Data Sheet ESBs can implement synchronous RAM, which is easier to use than asynchronous RAM. A circuit using asynchronous RAM must generate the RAM write enable (WE) signal while ensuring that its data and address signals meet setup and hold time specifications relative to the WE signal. In contrast, the ESB's synchronous RAM generates its own WE signal and is self-timed with respect to the global clock. Circuits using the ESB's selftimed RAM must only meet the setup and hold time specifications relative to the global clock. ESBs are grouped together in rows at the top and bottom of the device for fast horizontal communication. The ESB row interconnect can be driven by any ESB in the row. The row interconnect drives the ESB local interconnect, which in turn drives the ESB ports. ESB outputs drive the ESB local interconnect, which can drive row interconnect as well as all types of column interconnect, including leap lines. The leap lines allow fast access between ESBs and the adjacent LAB row. When implementing memory, each ESB can be configured in any of the following sizes for quad port and true dual-port memory modes: 256 x 16; 512 x 8; 1,024 x 4; 2,048 x 2; or 4,096 x 1. For dual-port and single-port modes, the ESB can be configured for 128 x 32 in addition to the list above. For variable port width RAMs, any port width ratio combination must be 1, 2, 4, 8, or 16. For example, a RAM with data ports of width 1 and 16 or 2 and 32 will work, but not 1 and 32. The ESB can also be split in half and used for two independent 2,048-bit single-port or dual-port RAM blocks. For example, one half of the ESB can be used as a 128 x 16 memory single-port memory while the other half can be used for a 1,024 x 2 dual-port memory. This effectively doubles the number of RAMs a Mercury device can implement for its given number of ESBs. The Quartus II software automatically merges two logical memory functions in a design into an ESB; the designer does not need to merge the functions manually. By combining multiple ESBs, the Quartus II software implements larger memory blocks automatically. For example, two 256 x 16 RAM blocks can be combined to form a 256 x 32 RAM block, and two 512 x 8 RAM blocks can be combined to form a 512 x 16 RAM block. Memory performance does not degrade for memory blocks up to 4,096 words deep. Each ESB can implement a 4,096-word-deep memory; the ESBs are used in parallel, eliminating the need for any external control logic and its associated delays. To create a high-speed memory block more than 4,096 words deep, the Quartus II software will automatically combine ESBs with LE control logic. 13 Tools Altera Corporation 37 Mercury Programmable Logic Device Family Data Sheet The ESB implements two forms of clocking modes for quad-port and dual-port memory--read/write clock mode and input/output clock mode. Read/Write Clock Mode An ESB implementing quad-port memory in read/write clock mode can use up to four clocks. For port A, one clock controls all registers associated with writing: data input, WE, and write address. The other clock controls all registers associated with reading: read enable (RE), read address, and data output. Another set of clocks can be used for port B of the RAM, or the same clocks can be used. Each ESB port, A or B, also supports independent read clock enable, write clock enable, and asynchronous clear signals. Read/write clock mode is commonly used for applications where reads and writes occur at different system frequencies. Figure 19 shows the ESB in read/write clock mode. 38 Altera Corporation (1) (2) (3) Four Dedicated Clocks Six Dedicated Inputs & Global Signals A B 6 Data In Q ENA D Notes to Figure 19: Tools Altera Corporation 4 Data In D ENA Q 4 6 Figure 19. ESB in Read/Write Clock Mode dataA[] RAM/ROM 128 x 32 (3) 256 x 16 512 x 8 1,024 x 4 2,048 x 2 4,096 x 1 dataB[] Read Address D ENA ENA Q Q D Read Address rdaddressB[] rdaddressA[] wraddressA[] D ENA Q Write Address Write Address Q D ENA wraddressB[] rdenB Notes (1), (2) rdenA Read Enable D ENA Q Read Enable Q D ENA outclkenA outclkenB wrenA Data Out[] D ENA D ENA Q Q Write Enable Write Enable Data Out[] Q D ENA Q D ENA wrenB inclkenA Write Pulse Generator inclkenB Write Pulse Generator inclockB inclockA Mercury Programmable Logic Device Family Data Sheet outclockA qA[] qB[] outclockB Only half of the ESB, either A or B, is used for dual-port configuration. All registers can be asynchronously cleared by ESB local interconnect signals, global signals, or the chip-wide reset. This configuration is supported for dual-port configuration. 39 13 Mercury Programmable Logic Device Family Data Sheet Input/Output Clock Mode An ESB using input/output clock mode can also use up to four clocks. On each of the two ports, A or B, one clock controls all registers for inputs into the ESB: data input, WE, RE, read address, and write address. The other clock controls the ESB data output registers. Each ESB port, A or B, also supports independent read clock enable, write clock enable, and asynchronous clear signals. Input/output clock mode is commonly used for applications where the reads and writes occur at the same system frequency, but require different clock enable signals for the input and output registers. Figure 20 shows the ESB in input/output clock mode. 40 Altera Corporation (1) (2) (3) Notes to Figure 20: Tools Altera Corporation Four Dedicated Clocks Six Dedicated Inputs & Global Signals A B 6 Data In Q ENA D 4 Data In D ENA Q 6 4 Figure 20. ESB in Input/Output Clock Mode dataA[ ] RAM/ROM 128 x 32 (3) 256 x 16 512 x 8 1,024 x 4 2,048 x 2 4,096 x 1 dataB[ ] Read Address D ENA ENA Q Q D Read Address rdaddressB[ ] rdaddressA[ ] wraddressA[ ] D ENA Q Write Address Write Address Q D ENA wraddressB[ ] rdenB rdenA Read Enable D ENA Q Read Enable Q D ENA Notes (1), (2) wrenA wrenB outclkenA Write Enable Data Out[] D ENA D ENA Q Q Write Enable Data Out[] Q D ENA Q D ENA outclkenB inclkenA Write Pulse Generator inclkenB Write Pulse Generator inclockB inclockA Mercury Programmable Logic Device Family Data Sheet outclockA qA[] qB[] outclockB Only half of the ESB, either A or B, is used for dual-port configuration. All registers can be asynchronously cleared by ESB local interconnect signals, global signals, or the chip-wide reset. This configuration is supported for dual-port configuration. 41 13 Mercury Programmable Logic Device Family Data Sheet Single-Port Mode The Mercury device's ESB also supports a single-port mode, which is used when simultaneous reads and writes are not required. See Figure 21. A single ESB can support up to two single-port mode RAMs. Figure 21. ESB in Single-Port Mode Dedicated Fast Global Signals Dedicated Clocks 4 6 RAM/ROM (2) 128 x 16 256 x 8 512 x 4 Data In 1,024 x 2 2,048 x 1 Data Out Address address[ ] D ENA Q D ENA Q Note (1) data[ ] D ENA Q To FastTrack Interconnect wren outclken Write Enable inclken inclock D ENA Q Write Pulse Generator outclock Notes to Figure 21: (1) (2) All registers can be asynchronously cleared by ESB local interconnect signals, global signals, or chip-wide reset. If there is only one single-port RAM block in an ESB, it can support the following configurations: 4,096 x 1; 2,048 x 2; 1,028 x 4; 512 x 8; 256 x 16; or 128 x 32. Content-Addressable Memory Mercury devices can implement CAM in ESBs. CAM can be thought of as the inverse of RAM. RAM stores data in a specific location; when the system submits an address, the RAM block provides the data. Conversely, when the system submits data to CAM, the CAM block provides the address where the data is found. For example, if the data FA12 is stored in address 14, the CAM outputs 14 when FA12 is driven into it. 42 Altera Corporation Mercury Programmable Logic Device Family Data Sheet CAM is used for high-speed search operations. When searching for data within a RAM block, the search is performed serially. Thus, finding a particular data word can take many cycles. CAM searches all addresses in parallel and outputs the address storing a particular word. When a match is found, a match flag is set high. CAM is ideally suited for applications such as Ethernet address lookup, data compression, pattern recognition, cache tags, fast routing table lookup, and high-bandwidth address filtering. Figure 22 shows the CAM block diagram. Figure 22. CAM Block Diagram data[ ] wraddress[ ] wren inclock inclocken inaclr data_address[ ] match outclock outclocken outaclr 13 The Mercury on-chip CAM provides faster system performance than traditional discrete CAM. Integrating CAM and logic into the Mercury device eliminates off-chip and on-chip delays, improving system performance. When in CAM mode, the ESB implements a 32-word, 32-bit CAM. Wider or deeper CAM, such as a 32-word, 64-bit or 128-word, 32-bit block, can be implemented by combining multiple CAM blocks with some ancillary logic implemented in LEs. The Quartus II software automatically combines ESBs and LEs to create larger CAM blocks. CAM supports writing "don't care" bits into words of the memory. The don't-care bit can be used as a mask for CAM comparisons; any bit set to don't-care has no effect on matches. CAM can generate outputs in three different modes: single-match mode, multiple-match mode, and fast multiple-match mode. In each mode, the ESB outputs the matched data's location as an encoded or unencoded address. When encoded, the ESB outputs an encoded address of the data's location. For instance, if the data is located in address 12, the ESB output is 12. When unencoded, each ESB port uses its 16 outputs to show the location of the data over two clock cycles. In this case, if the data is located in address 12, the 12th output line goes high. Figures 22 and 23 show the encoded CAM outputs and unencoded CAM outputs, respectively. Tools Altera Corporation 43 Mercury Programmable Logic Device Family Data Sheet Figure 23. Encoded CAM Address Outputs CAM addr[15..0] = 12 data[31..0] = 45 Data 15 27 45 85 Address 10 11 12 13 match = 1 Encoded Output Figure 24. Unencoded CAM Address Outputs CAM data[30..0] =45 (1) Data select (2) 15 27 45 85 Address 10 11 12 13 q12 q13 q14 q15 q0 Unencoded outputs. q12 goes high to signify a match. Notes to Figure 24: (1) (2) For an unencoded output, the ESB only supports 31 input data bits. One input bit is used by the select line to choose one of the two banks of 16 outputs. If the select input is a 1, then CAM outputs odd words between 1 through 15. If the select input is a 0, CAM outputs words even words between 0 through 14. In single-match mode, it takes two clock cycles to write into CAM, but only one clock cycle to read from CAM. In this mode, both encoded and unencoded outputs are available without external logic. Single-match mode is better suited for designs without duplicate data in the memory. 44 Altera Corporation Mercury Programmable Logic Device Family Data Sheet If the same data is written into multiple locations in the memory, a CAM block can be used in multiple-match or fast multiple-match modes. The ESB outputs the matched data's locations as an encoded or unencoded address. In multiple-match mode, it takes two clock cycles to write into a CAM block. For reading, there are 16 outputs from each ESB at each clock cycle. Therefore, it takes two clock cycles to represent the 32 words from a single ESB port. In this mode, encoded and unencoded outputs are available. To implement the encoded version, the Quartus II software adds a priority encoder with LEs. Fast multiple-match is identical to the multiple-match mode, however, it only takes one clock cycle to read from a CAM block and generate valid outputs. To do this, the entire ESB is used to represent 16 outputs. In fast multiple-match mode, the ESB can implement a maximum CAM block size of 16 words. A CAM block can be pre-loaded with data during configuration, or it can be written during system operation. In most cases, two clock cycles are required to write each word into CAM. When don't-care bits are used, a third clock cycle is required. f For more information on CAM, see Application Note 119 (Implementing High-Speed Search Applications with APEX CAM). 13 Tools Driving into ESBs ESBs provide flexible options for driving control signals. Different clocks can be used for the ESB inputs and outputs. Registers can be inserted independently on the data input, data output, read address, write address, WREN, and RDEN signals on each port of the ESB. The fast global signals and ESB local interconnect can drive the WREN and RDEN signals. The fast global signals, dedicated clock pins, and ESB local interconnect can drive the ESB clock signals. The ESB local interconnect is driven by the ESB row interconnects which, in turn, are driven by all types of column interconnects, including high-speed leap lines. Because the LEs drive the column interconnect to the ESB local interconnect, the LEs can control the WREN and RDEN signals and the ESB clock, clock enable, and asynchronous clear signals. Figure 25 shows the ESB control signal generation logic. Altera Corporation 45 Mercury Programmable Logic Device Family Data Sheet Figure 25. ESB Control Signal Generation Dedicated Clocks Fast Global Signals Local Interconnect Local Interconnect Local Interconnect Local Interconnect Local Interconnect Local Interconnect 4 6 INCLOCK OUTCLOCK INCLOCKEN OUTCLOCKEN RDEN WREN INCLR OUTCLR The ESB can drive row interconnects within its own ESB row and can directly drive all the column interconnects: column, priority column, and leap lines. Implementing Logic in ROM In addition to implementing RAM functions, the ESB can implement logic functions when it is programmed with a read-only pattern during configuration, creating a large LUT. With LUTs, combinatorial functions are implemented by looking up the results, rather than by computing them. This implementation of combinatorial functions can be faster than using algorithms implemented in general logic, a performance advantage further enhanced by the fast access times of ESBs. The large capacity of ESBs enables designers to implement complex functions in one logic level without the routing delays associated with linked LEs or distributed RAM blocks. Parameterized functions such as LPM functions can take advantage of the ESB automatically. Further, the Quartus II software can implement portions of a design with ESBs where appropriate. 46 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Programmable Speed/Power Control Mercury device ESBs offer the Turbo BitTM option, a high-speed mode that supports fast operation on an ESB-by-ESB basis. When high speed is not required, the Turbo Bit option can be turned off to reduce power dissipation by up to 50%. ESBs that run at low power incur a nominal timing delay adder. An ESB that is not used will be powered down so it does not consume DC current. Designers can program each ESB in the Mercury device for either highspeed or low-power operation. As a result, speed-critical paths in the design can run at high speed, while the remaining paths operate at reduced power. I/O Structure The IOE in Mercury devices contains a bidirectional I/O buffer and three registers for a complete embedded bidirectional IOE. The IOE contains individual input, output, and output enable registers. The input register can be used for external data requiring fast setup times. The output register can be used for data requiring fast clock-to-output performance. The output enable (OE) register can be used for fast clock-to-output enable timing. The Quartus II software automatically duplicates a single OE register that controls multiple output or bidirectional pins. For normal bidirectional operation, the input register can have its own clock input separate from the OE and output registers. The OE and output register share the same clock source. Each register can have its own clock enable signal from local interconnect in the associated LAB, fast global signals, or row global signals. 13 Tools Altera Corporation 47 Mercury Programmable Logic Device Family Data Sheet The Mercury IOE includes programmable delays that can be activated to ensure zero hold times, minimum clock-to-output times, input IOE register-to-core register transfers, or core-to-output IOE register transfers. A path in which a pin directly drives a register may require the delay to ensure zero hold time, whereas a path in which a pin drives a register through combinatorial logic may not require the delay. Programmable delays exist for decreasing input pin to core and IOE input register delays. The Quartus II Compiler can program these delays automatically to minimize setup time while providing a zero hold time. Delays are also programmable for increasing the register to pin delays for output and/or output enable registers. A programmable delay exists for increasing the tZX delay to the output pin, which is required for ZBT interfaces. Table 10 shows the programmable delays for Mercury devices. Table 10. Mercury Programmable Delay Chain Programmable Delays Input pin to core delay (1) Input pin to input register delay Output propagation delay Output enable register tCO delay Output tZX delay Note to Table 10: (1) This delay has four settings: off and three levels of delay. Quartus II Logic Option Decrease input delay to internal cells Decrease input delay to input register Increase delay to output pin Increase delay to OE pin Increase tZX delay to output pin The IOE registers in Mercury devices share the same source for clear or preset. Use of the preset/clear is programmable for each individual IOE. The register(s) can be programmed to power up high or low after configuration is complete. If programmed to power up low, an asynchronous clear can control the register(s). If programmed to power up high, an asynchronous preset can control the register(s). This feature prevents the inadvertent activation of another device's active-low input upon power-up. Figure 26 shows the IOE for Mercury devices. 48 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Figure 26. Mercury IOE Associated LAB Local Interconnect Two Row Local Fast Signals Six Fast Global Signals Four Dedicated Clocks Column and Priority Column Interconnect OE Register D Q Output tZX Delay VCCIO ENA CLRN/PRN Optional PCI Clamp OE Register tCO Delay VCCIO Programmable Pull-Up Chip-Wide Reset Output Register D Q Output Propagation Delay Drive Strength Control Open-Drain Output Slew Control ENA CLRN/PRN 13 Bus-Hold Circuit Input Pin to Core Delay (1) Tools Input Pin to Input Register Delay Input Register D Q ENA CLRN/PRN Priority Row Interconnect (for Associated LAB Row) Row Interconnect (for Associated LAB Row) Note to Figure 26: (1) This programmable delay has four settings: off and three levels of delay. Double Data Rate I/O Mercury device's have three register IOEs to support the DDRIO feature, which makes double data rate interfaces possible by clocking data on both positive and negative clock edges. The IOE in Mercury devices supports double data rate input and double data rate output modes. Altera Corporation 49 Mercury Programmable Logic Device Family Data Sheet In Mercury device IOEs, the OE register is a multi-purpose register available as a second input or output register. When using the IOE for double data rate inputs, the input register and OE register are automatically configured as input registers to clock input double rate data on alternating edges. An input latch is also used within the IOE for DDR input acquisition. The latch holds the data that is present during the clock high times, driving it to the OE register. This allows the OE register and input register to clock both bits of data into LEs, synchronous to the same clock edge (either rising or falling). Figure 27 shows an IOE configured for DDR input. Figure 27. IOE Configured for DDR Input Associated LAB Local Interconnect Two Row Local Fast Signals Six Fast Global Signals Four Dedicated Clocks VCCIO Optional PCI Clamp Column and Priority Column OE Register D Q VCCIO Programmable Pull-Up ENA CLRN/PRN Chip-Wide Reset Input Pin to Input Register Delay Input Register D Q Bus-Hold Circuit ENA CLRN/PRN PRN D ENA Latch Priority Row (for Associated LAB Row) Row (for Associated LAB Row) Q 50 Altera Corporation Mercury Programmable Logic Device Family Data Sheet When using the IOE for double data rate outputs, the output register and OE register are automatically configured to clock two data paths from LEs on rising clock edges. These register outputs are multiplexed by the clock to drive the output pin at a x2 rate. The output register clocks the first bit out on the clock high time, while the OE register clocks the second bit out on the clock low time. Figure 28 shows the IOE configured for DDR output. Figure 28. IOE Configured for DDR Output Associated LAB Local Interconnect Two Row Local Fast Signals Six Fast Global Signals Four Dedicated Clocks OE Register D Q VCCIO ENA CLRN/PRN 13 Optional PCI Clamp VCCIO Tools Programmable Pull-Up Chip-Wide Reset Output Register D Q 0 1 Output Propagation Delay ENA CLRN/PRN Drive Strength Control Open-Drain Output Slew Control Bus-Hold Circuit Bidirectional DDR on an I/O pin is possible by using the IOE for DDR output and using LEs to acquire the double data rate input. Bidirectional DDR I/O pins support double data rate synchronous DRAM (DDR SDRAM) at 166 MHz (334 Mbps), which transfer data on a double data rate bidirectional bus. QDR SRAMs are also supported with DDR I/O pins on separate read and write ports. Altera Corporation 51 Mercury Programmable Logic Device Family Data Sheet Zero Bus Turnaround SRAM Interface Support In addition to DDR SDRAM support, Mercury device I/O pins also support interfacing with ZBT SRAM blocks at up to 200 MHz. ZBT SRAM blocks are designed to eliminate dead bus cycles when turning a bidirectional bus around between reads and writes, or writes and reads. ZBT allows for 100% bus utilization because ZBT SRAM can read or write on every clock cycle. To avoid bus contention, the output tZX delay ensures that the clock-tolow-impedance time (tZX) is greater than the clock-to-high-impedance time (tXZ). Time delay control of clocks to the OE/output and input register, using a single general purpose PLL, enable the Mercury device to meet ZBT tCO and tSU times. Programmable Drive Strength The output buffer for each Mercury device I/O pin has a programmable drive strength control for certain I/O standards. The LVTTL standard has several levels of drive strength that can be controlled by the user. SSTL-3 class I and II, SSTL-2 class I and II, HSTL class I and II, and 3.3-V GTL+ support a minimum or maximum setting. The minimum setting is the lowest drive strength that guarantees the IOH/IOL of the standard. The maximum setting provides higher drive strength that allows for faster switching and is the default setting. Using settings below the maximum provides signal slew-rate control to reduce system noise and signal overshoot. Table 11 shows the possible settings for the I/O standards with drive strength control. 52 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Table 11. Programmable Drive Strength I/O Standard LVTTL (3.3 V) IOH/IOL Current Strength Setting 4 mA 8 mA 12 mA 16 mA 24 mA (default) LVTTL (2.5 V) 4 mA 8 mA 12 mA 16 mA (default) LVTTL (1.8 V) SSTL-3 class I and II SSTL-2 class I and II HSTL class I and II GTL+ (3.3 V) 2 mA 4 mA (default) Minimum Maximum (default) 13 Tools Open-Drain Output Mercury devices provide an optional open-drain (equivalent to an opencollector) output for each I/O pin. This open-drain output enables the device to provide system-level control signals (e.g., interrupt and write enable signals) that can be asserted by any of several devices. Slew-Rate Control The output buffer for each Mercury device I/O pin has a programmable output slew rate control that can be configured for low-noise or highspeed performance. A faster slew rate provides high-speed transitions for high-performance systems. However, these fast transitions may introduce noise transients into the system. A slow slew rate reduces system noise, but adds a nominal delay to rising and falling edges. Each I/O pin has an individual slew rate control, allowing the designer to specify the slew rate on a pin-by-pin basis. The slew rate control affects both the rising and falling edges. Altera Corporation 53 Mercury Programmable Logic Device Family Data Sheet Bus Hold Each Mercury device I/O pin provides an optional bus-hold feature. When this feature is enabled for an I/O pin, the bus-hold circuitry weakly holds the signal at its last driven state. By holding the last driven state of the pin until the next input signal is present, the bus-hold feature eliminates the need to add external pull-up or pull-down resistors to hold a signal level when the bus is tri-stated. The bus-hold circuitry also pulls undriven pins away from the input threshold voltage where noise can cause unintended high-frequency switching. This feature can be selected individually for each I/O pin. The bus-hold output will drive no higher than VCCIO to prevent overdriving signals. If the bus-hold feature is enabled, the programmable pull-up option cannot be used. The bus-hold feature should also be disabled if open-drain outputs are used with the GTL+ I/O standard. The bus-hold circuitry weakly pulls the signal level to the last driven state through a resistor with a nominal resistance (RBH) of approximately 8 k. Table 42 gives specific sustaining current that will be driven through this resistor and overdrive current that will identify the next driven input level. This information is provided for each VCCIO voltage level. The bus-hold circuitry is active only after configuration. When going into user mode, the bus-hold circuit captures the value on the pin present at the end of configuration. Programmable Pull-Up Resistor Each Mercury device I/O pin provides an optional programmable pullup resistor during user mode. When this feature is enabled for an I/O pin, the pull-up resistor (50 k) weakly holds the output to the VCCIO level of the bank that the output pin resides in. I/O Row Bands The I/O row bands are one of the advanced features of the Mercury architecture. All IOEs are grouped in I/O row bands across the device. The number of I/O row bands depends on the Mercury device size. The I/O row bands are designed for flip-chip technology, allowing I/O pins to be distributed across the entire chip, not only in the periphery. This array driver technology allows higher I/O pin density (I/O pins per device area) than peripheral I/O pins. 54 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Each row of I/O pins has an associated LAB row for driving to and from the core of the Mercury device. For a given I/O band row, its associated LAB row is located below it with the exception of the bottom I/O band row. The bottom I/O band is located at the bottom periphery of the device, hence its associated LAB row is located above it. Figure 29 shows an example of an I/O band to associated LAB row interconnect in a Mercury device. There is a maximum of two IOEs associated with each LAB in the associated LAB row. The local interconnect of the associated LAB drives the IOEs. Since local interconnect is shared with the LAB neighbor, any given LAB can directly drive up to four IOEs. The local interconnect drives the data and OE signals when the IOE is used as an output or bidirectional pin. Figure 29. IOE Connection to Interconnects and Adjacent LAB IOE Pair IOE Pair Note (1) IOE Pair All Column Interconnects IOE INC IOE INC IOE INC IOE INC IOE INC IOE INC INB OUT INA INB OUT INA INB OUT INA INB OUT INA INB OUT INA INB OUT INA I/O Band Row 13 Tools Row Interconnect Priority Row Interconnect LAB To Local Interconnect LAB LAB To Next LAB Associated LAB Row IOE pairs drive unregistered inputs to the associated LAB's local interconnect. The associated LAB and its neighbor can drive a given IOE pair through the local interconnect. Associated LAB to IOE Pair Local Interconnect Note to Figure 29: (1) INA: unregistered input; INB: registered/unregistered input; INC: registered/unregistered input or OE register output in DDR mode. The IOEs drive registered or combinatorial versions of input data into the device. The unregistered input data can be driven to the local interconnect (for fast input setup), row and priority row interconnect, and column and priority column interconnects. The registered data can also be driven to the same row and column resources. The OE register output can be fed back through column and row interconnects to implement DDR I/O pins. Altera Corporation 55 Mercury Programmable Logic Device Family Data Sheet Dedicated Fast Lines & I/O Pins Mercury devices incorporate dedicated bidirectional pins for signals with high internal fanout, such as PCI control signals. These pins are called dedicated fast I/O pins (FAST1, FAST2, FAST3, FAST4, FAST5, and FAST6) and can drive the six global fast lines throughout the device, ideal for fast clock, clock enable, clear, preset, or high fanout logic signal distribution. The dedicated fast I/O pins have the same IOE as a regular I/O pin. The dedicated fast lines can also be driven by a LE local interconnect to generate internal global signals. In addition to the device global fast lines, each LAB row has two dedicated fast lines local to the row. This is ideal for high fanout control signals for a section of a design that may fit into a single LAB row. Each I/O band (with the exception of the top I/O band) has two dedicated row-global fast I/O pins to drive the row-global fast resources for the associated LAB. The dedicated local fast I/O pins have the same IOE as a regular I/O pin. The LE local interconnect can drive dedicated row-global fast lines to generate internal global signals specific to a row. There are no pin connections for buried LAB rows; LE local interconnects drive the rowglobal signals in those rows. I/O Standard Support Mercury device IOEs support the following I/O standards: LVTTL LVCMOS 1.8-V 2.5-V 3.3-V PCI 3.3-V PCI-X 3.3-V AGP (1x, 2x) LVDS LVPECL 3.3-V PCML GTL+ HSTL class I and II SSTL-3 class I and II SSTL-2 class I and II CTT 56 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Table 12 describes the I/O standards supported by Mercury devices. Table 12. Mercury Supported I/O Standards I/O Standard Type Input Reference Voltage (VREF) (V) N/A N/A N/A N/A N/A N/A N/A N/A N/A 1.0 0.75 1.25 1.5 1.32 1.5 Output Supply Voltage (VCCIO) (V) 3.3 3.3 2.5 1.8 3.3 3.3 3.3 3.3 3.3 N/A 1.5 2.5 3.3 3.3 3.3 Board Termination Voltage (VTT) (V) N/A N/A N/A N/A N/A N/A N/A N/A 3.3 1.5 0.75 1.25 LVTTL LVCMOS 2.5 V 1.8 V 3.3-V PCI 3.3-V PCI-X LVDS LVPECL 3.3-V PCML GTL+ HSTL class I and II SSTL-2 class I and II SSTL-3 class I and II AGP CTT Single-ended Single-ended Single-ended Single-ended Single-ended Single-ended Differential Differential Differential Voltage referenced Voltage referenced Voltage referenced Voltage referenced Voltage referenced Voltage referenced 13 Tools 1.5 N/A 1.5 Each regular I/O band row contains two I/O banks. The number of I/O banks in a Mercury device depends on the number of I/O band rows. The top I/O band contains four regular I/O banks specifically designed for HSDI. The top I/O band banks and dedicated clock inputs support LVDS, LVPECL, and 3.3-V PCML. 3.3-V PCML is an open-drain standard and therefore requires external termination to 3.3 V. All other standards are supported by all I/O banks. The top I/O banks 1, 2, 3, and 4 only support non-HSDI I/O pins if the design does not use HSDI circuitry. If the design uses any HSDI channel, banks 1, 2, 3, and 4 all do not support regular I/O pins. Additionally, the EP1M350 device includes the Flexible-LVDS feature, providing support for up to 100 LVDS channels on all regular I/O banks. Regular I/O banks in EP1M350 devices include dedicated LVDS input and output buffers that do not require any external components except for 100- termination resistors on receiver channels. Altera Corporation 57 Mercury Programmable Logic Device Family Data Sheet For the HSDI I/O band, half of the dedicated banks support LVDS, 3.3-V PCML or LVPECL, and receiver inputs, while the other half support LVDS, PCML or LVPECL, and transmitter outputs. A single device can support 1.5-V, 1.8-V, 2.5-V, and 3.3-V interfaces; each bank can support a VCCIO standard independently. Each bank can also use a separate VREF level so that each bank can support any of the terminated standards (such as SSTL-3) independently. A bank can support a single VREF level. Each bank contains a fixed VREF pin for voltage referenced standards. This pin can be used as a regular I/O if a VREF standard is not used. Table 13 shows the number of I/O banks in each Mercury device. Table 13. Number of I/O Banks per Device Device EP1M120 EP1M350 Regular I/O Banks 8 12 HSDI Band I/O Banks 4 4 Each bank can support multiple standards with the same VCCIO for output pins. For EP1M120 devices, each bank can support one voltage-referenced I/O standard, but can support multiple I/O standards with the same VCCIO and VREF voltage levels. For example, when VCCIO is 3.3 V, a bank can support LVTTL, LVCMOS, 3.3-V PCI, and SSTL-3 for inputs and outputs. Figure 30 shows the I/O bank layout for an EP1M120 device. For EP1M350 devices, each bank can support two voltage-reverenced I/O standards; each I/O bank is split into two voltage-referenced sub-banks. When using the two HSDI transmitter banks as regular I/O banks in a non-HSDI mode, those two banks require the same VCCIO level. However, each HSDI transmitter bank supports its own VREF level. 58 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Figure 30. I/O Bank Layout ESB ESB ESB ESB ESB ESB I/O or HSDI Banks Input, Output, or HSDI Receiver (1) Input, Output, or HSDI Transmitter (1), (2) Input, Output, or HSDI Receiver (1) Input, Output, or HSDI Transmitter (1), (2) Regular I/O Banks I/O Bank I/O Bank I/O Bank I/O Bank I/O Bank I/O Bank 13 I/O Bank ESB ESB ESB ESB I/O Bank Tools ESB ESB Notes to Figure 30: (1) (2) If HSDI I/O channels are not used, the HSDI banks can be used as regular I/O banks. When used as regular I/O banks, these banks must be set to the same VCCIO level, but can have separate VREF bank settings. f For more information on I/O standards, see Application Note 117 (Using Selectable I/O Standards in Altera Devices). MultiVolt I/O Interface The Mercury architecture supports the MultiVolt I/O interface feature, which allows Mercury devices in all packages to interface with devices with different supply voltages. The devices have one set of VCC pins for internal operation and input buffers (VCCINT), and another set for I/O output drivers (VCCIO). Altera Corporation 59 Mercury Programmable Logic Device Family Data Sheet The Mercury VCCINT pins must always be connected to a 1.8-V power supply. With a 1.8-V VCCINT level, input pins are 1.8-V, 2.5-V and 3.3-V tolerant. The VCCIO pins can be connected to either a 1.5-V, 1.8-V, 2.5-V or 3.3-V power supply, depending on the output requirements. When VCCIO pins are connected to a 1.5-V power supply, the output levels are compatible with HSTL systems. When VCCIO pins are connected to a 1.8-V power supply, the output levels are compatible with 1.8-V systems. When VCCIO pins are connected to a 2.5-V power supply, the output levels are compatible with 2.5-V systems. When the VCCIO pins are connected to a 3.3-V power supply, the output high is 3.3 V and is compatible with 3.3-V or 5.0-V systems. Table 14 summarizes Mercury MultiVolt I/O support. Table 14. Mercury MultiVolt I/O Support VCCIO (V) 1.5 1.8 2.5 3.3 (1) (2) Note (1) Output Signal 3.3 V v v v v v (6) Input Signal 1.5 V v v (2) v (2) v (2) 1.8 V v v v (2) v (2) 2.5 V v v v v (2) 5.0 V 1.5 V v 1.8 V v (3) v (4) 2.5 V 3.3 V 5.0 V v v (5) v v Notes to Table 14: The PCI clamping diode must be disabled to drive an input with voltages higher than V CCIO unless an external resistor is used. These input levels are only available if the input standard is set to any VREF-based input standard (SSTL-2, SSTL-3, HSTL, GTL+, AGP 2x). The input buffers are powered from VCCINT when using V REF-based input standards. LVTTL, PCI, PCI-X, AGP 1x input buffers are powered by VCCIO. Therefore, these standards cannot be driven with input levels below the V CCIO setting except for when VCCIO = 3.3 V and the input voltage (VI) = 2.5 V. When VCCIO = 1.8 V, the Mercury device can drive a 1.5-V device with 1.8-V tolerant inputs. When VCCIO = 2.5 V, the Mercury device can drive a 1.8-V device with 2.5-V tolerant inputs. When VCCIO = 3.3 V, the Mercury device can drive a 2.5-V device with 3.3-V tolerant inputs. Designers can set Mercury devices to be 5.0-V tolerant by adding an external resistor and enabling the PCI clamping diode. (3) (4) (5) (6) Power Sequencing & Hot-Socketing Because Mercury devices can be used in a mixed-voltage environment, the devices are designed specifically to tolerate any possible power-up sequence. Therefore, the VCCIO and VCCINT power supplies may be powered in any order. Signals can be driven into Mercury devices before and during power-up without damaging the device. In addition, Mercury devices do not drive out during power-up. Once operating conditions are reached and the device is configured, Mercury devices operate as specified by the user. 60 Altera Corporation Mercury Programmable Logic Device Family Data Sheet General Purpose PLL Mercury devices have ClockLockTM, ClockBoostTM, and advanced ClockShiftTM features, which use up to four general-purpose PLLs (separate from the two HSDI PLLs) to province clock management and clock-frequency synthesis. EP1M120 devices contain two general purpose PLLs; EP1M350 devices contain four general purpose PLLs. These PLLs allow designers to increase performance and provide clock-frequency synthesis. The PLL reduces the clock delay within a device. This reduction minimizes clock-to-output and setup times while maintaining zero hold times. The PLLs, which provide programmable multiplication, allow the designer to distribute a low-speed clock and multiply that clock ondevice. Mercury devices include a high-speed clock tree: unlike ASICs, the user does not have to design and optimize the clock tree. The PLLs work in conjunction with the Mercury device's high-speed clock to provide significant improvements in system performance and bandwidth. Table 15 shows the general purpose PLL features for Mercury devices. Figure 31 shows a Mercury PLL. Table 15. Mercury General Purpose PLL Features Device EP1M120 EP1M350 Note to Table 15: (1) n represents the prescale divider for the PLL input. k, p, q, and v represent the different post scale dividers for the four possible PLL outputs. m, k, p, and q are integers that range from 1 to 160. n and v are integers that can range from 1 to 16. Number of PLLs 2 4 ClockBoost Feature (1) m/(n x k, p, q, v) m/(n x k, p, q, v) Number of External Clock Outputs 2 4 Number of Feedback Inputs 2 4 Advanced ClockShift v v 13 Tools Figure 31. Mercury General-Purpose PLL Phase Comparator Voltage-Controlled Oscillator inclock n k Phase Shift Circuitry Time Delay/Shift Time Delay/Shift Time Delay/Shift Time Delay/Shift clock0 p clock1 q clock2 m fbin v clock_ext ClockLock Altera Corporation 61 Mercury Programmable Logic Device Family Data Sheet The PLLs in Mercury devices are enabled through the Quartus II software. External devices are not required to use these features. Advanced ClockBoost Multiplication & Division Each Mercury PLL includes circuitry that provides clock synthesis for up to four outputs (three internal outputs and one external output) using m/(n x output divider) scaling. When a PLL is locked, the locked output clock aligns to the rising edge of the input clock. The closed loop equation for Figure 31 gives an output frequency fclock0 = (m/(n x k))fIN, fclock1 = (m/(n x p))fIN, fclock2 = (m/(n x q))fIN, and fclock_ext = (m/(n x v))fIN or fclock1. These equations allow the multiplication or division of clocks by a programmable number. The Quartus II software automatically chooses the appropriate scaling factors according to the frequency, multiplication, and division values entered. A single PLL in a Mercury device allows for multiple user-defined multiplication and division ratios that are not possible even with multiple delay-locked loops (DLLs). For example, if a frequency scaling factor of 3.75 is needed for a given input clock, a multiplication factor of 15 and a division factor of 4 can be entered. This advanced multiplication scaling can be performed with a single PLL, making it unnecessary to cascade PLL outputs. External Clock Outputs Mercury devices have four low-jitter external clocks available for external clock sources. Other devices on the board can use these outputs as clock sources. There are three modes for external clock outputs. Multiplication is allowed in all external clock output modes. Zero Delay Buffer: The external clock output pin is phase aligned with the clock input pin for zero delay. Programmable phase shift and time delay shift are not allowed in this configuration. Multiplication is allowed with the zero delay buffer mode. The MegaWizard interface for altclklock should be used to verify possible clock settings. External Feedback: The external feedback input pin is phase aligned with clock input pin. By aligning these clocks, you can actively remove clock delay and skew between devices. Multiplication is allowed with the external feedback mode. This mode has the same restrictions as zero delay buffer mode. 62 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Normal Mode: The external clock output pin will have phase delay relative to the clock input pin. If an internal clock is used in this mode, the IOE register clock will be phase aligned to the input clock pin. Multiplication is allowed with the normal mode. Advanced ClockShift Circuitry General purpose PLLs in Mercury devices have advanced ClockShiftTM circuitry that provides programmable phase shift and fine tune time delay shift. For phase shifting, users can enter a phase shift (in degrees or time units) that affects all PLL outputs. Phase shifts of 90, 180, and 270 can be implemented exactly. Other values of phase shifting, or delay shifting in time units, are allowed with a resolution range of 0.3 ns to 1.0 ns. This resolution varies with frequency input and the user-entered multiplication and division factors. The phase shift ability is only possible on a multiplied or divided clock if the input and output frequency have an integer multiple relationship (i.e., fIN/fOUT or fOUT/fIN must be an integer). In addition to the phase shift feature that affects all outputs, there is an advanced fine time delay shift control on each of the four PLL outputs. Each PLL output can be shifted in 250-ps increments for a range of -2.0 ns to +2.0 ns. This ability can be used in conjunction with the phase shifting ability that affects all outputs. fIN/fOUT does not need to have an integer relationship for the advanced fine time delay shift control. 13 Tools Clock Enable Signal Mercury PLLs have a CLKLK_ENA pin for enabling/disabling all of the device PLLs. When the CLKLK_ENA pin is high, the PLL drives a clock to all its output ports. When the CLKLK_ENA pin is low, the clock0, clock1, clock2 and extclock ports are driven by GND and all of the PLLs go out of lock. When the CLKLK_ENA pin goes high again, the PLL must relock. The individual enable port for each general purpose PLL is programmable. If more than one general-purpose PLL is instantiated, each one does not have to use the clock enable. To enable/disable the device PLLs with the CLKLK_ENA pin, the inclocken port on the altclklock instance must be connected to the CLKLK_ENA input pin. Altera Corporation 63 Mercury Programmable Logic Device Family Data Sheet Lock Signals The Mercury device general purpose PLL circuits support individual LOCK signals. The LOCK signal drives high when the PLL has locked onto the input clock. Lock remains high as long as the input remains within specification. It will go low if the input is out of specification. A LOCK pin is optional for each PLL used in the Mercury devices; when not used, they are I/O pins. This signal is not available internally; if it is used in the core, it must be fed back in with an input pin. SignalTap Embedded Logic Analyzer Mercury devices include device enhancements to support the SignalTap embedded logic analyzer. By including this circuitry, the Mercury device provides the ability to monitor design operation over a period of time through the IEEE Std. 1149.1 JTAG circuitry; a designer can analyze internal logic at speed without bringing internal signals to the I/O pins. This feature is particularly important for advanced packages such as FineLine BGA packages, because it can be difficult to add a connection to a pin during the debugging process after a board is designed and manufactured. All Mercury devices provide JTAG BST circuitry that complies with the IEEE Std. 1149.1-1990 specification. JTAG boundary-scan testing can be performed before or after configuration, but not during configuration. Mercury devices can also use the JTAG port for configuration with the Quartus II software or with hardware using either Jam Standard Test and Programming Language (STAPL) Files (.jam) or Jam STAPL Byte-Code Files (.jbc). Mercury devices also use the JTAG port to monitor the logic operation of the device with the SignalTap embedded logic analyzer. Mercury devices support the JTAG instructions shown in Table 16. IEEE Std. 1149.1 (JTAG) Boundary-Scan Support 64 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Table 16. Mercury JTAG Instructions JTAG Instruction Description SAMPLE/PRELOAD Allows a snapshot of signals at the device pins to be captured and examined during normal device operation and permits an initial data pattern to be output at the device pins. Also used by the SignalTap embedded logic analyzer. EXTEST BYPASS Allows the external circuitry and board-level interconnections to be tested by forcing a test pattern at the output pins and capturing test results at the input pins. Places the 1-bit bypass register between the TDI and TDO pins, which allows the BST data to pass synchronously through selected devices to adjacent devices during normal device operation. Selects the 32-bit USERCODE register and places it between the TDI and TDO pins, allowing the USERCODE to be serially shifted out of TDO. Selects the IDCODE register and places it between TDI and TDO, allowing the IDCODE to be serially shifted out of TDO. These instructions are used when configuring a Mercury device via the JTAG port with a ByteBlasterMVTM download cable, or using a Jam STAPL or Jam Byte-Code file via an embedded processor. These instructions monitor internal device operation with the SignalTap embedded logic analyzer. USERCODE IDCODE ICR Instructions SignalTap Instructions 13 Tools The Mercury device instruction register length is 10 bits. The Mercury device USERCODE register length is 32 bits. Tables 17 and 18 show the boundary-scan register length and device IDCODE information for Mercury devices. Table 17. Mercury Boundary-Scan Register Length Device EP1M120 EP1M350 Boundary-Scan Register Length (Bits) 1,125 1,695 Table 18. 32-Bit Mercury Device IDCODE Device Version (4 Bits) EP1M120 EP1M350 (1) (2) IDCODE (32 Bits) (1) Part Number (16 Bits) 0011 0000 0000 0000 0011 0000 0000 0001 Manufacturer Identity (11 Bits) 000 0110 1110 000 0110 1110 1 (1 Bit) (2) 1 1 0000 0000 Notes to Table 18: The most significant bit (MSB) is on the left. The IDCODE's least significant bit (LSB) is always 1. Altera Corporation 65 Mercury Programmable Logic Device Family Data Sheet Figure 32 shows the timing requirements for the JTAG signals. Figure 32. Mercury JTAG Waveforms TMS TDI t JCP t JCH TCK tJPZX TDO tJSSU Signal to Be Captured Signal to Be Driven tJSH t JPCO t JPXZ t JCL t JPSU t JPH tJSZX tJSCO tJSXZ Table 19 shows the JTAG timing parameters and values for Mercury devices. Table 19. Mercury JTAG Timing Parameters & Values Symbol tJCP tJCH tJCL tJPSU tJPH tJPCO tJPZX tJPXZ tJSSU tJSH tJSCO tJSZX tJSXZ TCK clock period TCK clock high time TCK clock low time JTAG port setup time JTAG port hold time JTAG port clock to output JTAG port high impedance to valid output JTAG port valid output to high impedance Capture register setup time Capture register hold time Update register clock to output Update register high impedance to valid output Update register valid output to high impedance 20 45 35 35 35 Parameter Min 100 50 50 20 45 Max Unit ns ns ns ns ns 25 25 25 ns ns ns ns ns ns ns ns 66 Altera Corporation Mercury Programmable Logic Device Family Data Sheet f For more information, see the following documents: Application Note 39 (IEEE Std. 1149.1 (JTAG) Boundary-Scan Testing in Altera Devices) Jam Programming & Test Language Specification Generic Testing Each Mercury device is functionally tested. Complete testing of each configurable static random access memory (SRAM) bit and all logic functionality ensures 100% yield. AC test measurements for Mercury devices are made under conditions equivalent to those shown in Figure 33. Multiple test patterns can be used to configure devices during all stages of the production flow. 13 Tools Altera Corporation 67 Mercury Programmable Logic Device Family Data Sheet Figure 33. Mercury AC Test Conditions Power supply transients can affect AC measurements. Simultaneous transitions of multiple outputs should be avoided for accurate measurement. Threshold tests must not be performed under AC conditions. Large-amplitude, fast-groundcurrent transients normally occur as the device outputs discharge the load capacitances. When these transients flow through the parasitic inductance between the device ground pin and the test system ground, significant reductions in observable noise immunity can result. Device Output To Test System Device input rise and fall times < 3 ns C1 (includes jig capacitance) Operating Conditions Table 20 through 43 provide information on absolute maximum ratings, recommended operating conditions, DC operating conditions, and capacitance for 1.8-V Mercury devices. Note (1) Minimum -0.5 -0.5 -0.5 -34 No bias Under bias BGA packages under bias -65 -65 Table 20. Mercury Device Absolute Maximum Ratings Symbol VCCINT VCCIO VI IOUT TSTG TAMB TJ DC input voltage DC output current, per pin Storage temperature Ambient temperature Junction temperature Parameter Supply voltage Conditions With respect to ground (2) Maximum 2.5 4.6 4.6 34 150 135 135 Unit V V V mA C C C 68 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Table 21. Mercury Device Recommended Operating Conditions Symbol VCCINT VCCIO Parameter Supply voltage for internal logic and input buffers (3) Conditions Minimum 1.71 3.00 (3.135) 2.375 1.71 1.4 -0.5 0 0 -40 Maximum 1.89 3.60 (3.465) 2.625 1.89 1.6 4.1 VCCIO 85 100 40 40 Unit V V V V V V V C C ns ns Supply voltage for output buffers, (3), (4) 3.3-V operation Supply voltage for output buffers, (3) 2.5-V operation Supply voltage for output buffers, (3) 1.8-V operation Supply voltage for output buffers, (3) 1.5-V operation VI VO TJ Input voltage Output voltage Operating temperature (2), (5) For commercial use For industrial use 13 Tools tR tF Input rise time Input fall time Table 22. Mercury Device DC Operating Conditions Symbol II IOZ ICC0 Note (6), (7) Minimum -10 -10 30 40 50 60 20 30 60 50 80 150 Parameter Input pin leakage current Tri-stated I/O pin leakage current VCC supply current (standby) for EP1M120 devices VCC supply current (standby) for EP1M350 devices Conditions VI = VCCIOmax to 0 V (5) VO = VCCIOmax to 0 V (5) For commercial use (8) For Industrial use (8) For commercial use (8) For Industrial use (8) Typical Maximum 10 10 Unit A A mA mA mA mA k k k RCONF Value of I/O pin pull- VCCIO = 3.0 V (9) up resistor before VCCIO = 2.375 V (9) and during VCCIO = 1.71 V (9) configuration Altera Corporation 69 Mercury Programmable Logic Device Family Data Sheet Table 23. LVTTL Specifications Symbol VCCIO VI H VIL II VOH VOL Note (10) Conditions Minimum 3.0 1.7 -0.5 VIN = 0 V or VCCIO IOH = -4 mA IOL = 4 mA -10 2.4 0.45 Parameter Output supply voltage High-level input voltage Low-level input voltage Input pin leakage current High-level output voltage Low-level output voltage Maximum 3.6 4.1 0.7 10 Units V V V A V V Table 24. LVCMOS Specifications Symbol VCCIO VIH VIL II VOH VOL Parameter Power supply voltage range High-level input voltage Low-level input voltage Input pin leakage current High-level output voltage Low-level output voltage Conditions Minimum 3.0 1.7 -0.5 Maximum 3.6 4.1 0.7 10 Units V V V A V VIN = 0 V or VCCIO VCCIO = 3.0, IOH = -0.1 mA VCCIO = 3.0, IOL = 0.1 mA -10 VCCIO - 0.2 0.2 V Table 25. 2.5-V I/O Specifications Symbol VCCIO VIH VIL II VOH Note (10) Conditions Minimum 2.375 1.7 -0.5 VIN = 0 V or VCCIO IOH = -0.1 mA IOH = -1 mA IOH = -2 mA 10 2.1 2.0 1.7 0.2 0.4 0.7 Parameter Output supply voltage High-level input voltage Low-level input voltage Input pin leakage current High-level output voltage Maximum 2.625 4.1 0.7 10 Units V V V A V V V V V V VOL Low-level output voltage IOL = 0.1 mA IOH = 1 mA IOH = 2 mA 70 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Table 26. 1.8-V I/O Specifications Symbol VCCIO VI H VIL II VOH VOL Note (10) Conditions Minimum 1.71 0.65 x VCCIO -0.5 VIN = 0 V or VCCIO IOH = -2 mA IOL = 2 mA -10 VCCIO - 0.45 0.45 Parameter Output supply voltage High-level input voltage Low-level input voltage Input pin leakage current High-level output voltage Low-level output voltage Maximum 1.89 4.1 0.35 x VCCIO 10 Units V V V A V V Figures 34 and 35 show receiver input and transmitter output waveforms, respectively, for all differential I/O standards (LVPECL, 3.3-V PCML, LVDS, and HyperTransport technology). Figure 34. Receiver Input Waveforms for Differential I/O Standards Single-Ended Waveform Positive Channel (p) = VIH VID Negative Channel (n) = VIL VCM 13 Tools Ground Differential Waveform +VID p-n=0V VID (Peak-to-Peak) - VID Altera Corporation 71 Mercury Programmable Logic Device Family Data Sheet Figure 35. Transmitter Output Waveforms for Differential I/O Standards Single-Ended Waveform Positive Channel (p) = VOH VOD Negative Channel (n) = VOL VCM Ground Differential Waveform +VOD p-n=0V VOD (Peak-to-Peak) - VOD Table 27. 3.3-V LVDS I/O Specifications Symbol VCCIO VOD VOD VOS VOS VTH VIN RL Parameter I/O supply voltage Differential output voltage Change in VOD between high and low Output offset voltage Change in VOS between high and low Receiver input voltage range Receiver differential input resistor (external to Mercury devices) Conditions RL = 100 RL = 100 RL = 100 RL = 100 Minimum 3.135 250 Typical 3.3 510 Maximum 3.465 600 50 Units V mV mV V mV mV V 1.125 1.25 1.375 50 Differential input threshold VCM = 1.2 V -100 0.0 90 100 100 2.4 110 72 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Table 28. 3.3-V PCML Specifications Symbol VCCIO VIL VIH VOL VOH VT VID VOD tR tF tDSKEW R1 (11) R2 (11) Parameter I/O supply voltage Low-level input voltage High-level input voltage Low-level output voltage High-level output voltage Output termination voltage Differential input voltage Differential output voltage Rise time (20 to 80%) Fall time (20 to 80%) Differential skew Output load Receiver differential input resistor Conditions Minimum 3.135 Typical 3.3 Maximum 3.465 VCCIO - 0.4 Units V V V VCCIO VCCIO - 0.4 VCCIO VCCIO 400 400 700 800 800 200 200 25 90 45 100 50 110 55 V V V mV mV ps ps ps 13 Tools Table 29. LVPECL Specifications Symbol VCCIO VIL VIH VOL VOH VID VOD tR tF tDSKEW RL Parameter I/O supply voltage Low-level input voltage High-level input voltage Low-level output voltage High-level output voltage Differential input voltage Differential output voltage Rise time (20 to 80%) Fall time (20 to 80%) Differential skew Receiver differential input resistor Conditions Minimum 3.135 0 400 1,400 2,275 400 525 85 85 Typical 3.3 Maximum 3.465 2,000 2,470 1,650 2,470 Units V mV mV mV mV mV mV ps ps ps 600 1,050 1,200 1,200 325 325 25 100 Altera Corporation 73 Mercury Programmable Logic Device Family Data Sheet Table 30. 3.3-V PCI Specifications Symbol VCCIO VIH VIL II VOH VOL Parameter I/O supply voltage High-level input voltage Low-level input voltage Input pin leakage current High-level output voltage Low-level output voltage Conditions Minimum 3.0 0.5 x VCCIO -0.5 Typical 3.3 Maximum 3.6 VCCIO + 0.5 0.3 x VCCIO 10 Units V V V A V 0 < VIN < VCCIO IOUT = -500 A IOUT = 1,500 A -10 0.9 x VCCIO 0.1 x VCCIO V Table 31. PCI-X Specifications Symbol VCCIO VIH VIL VIPU IIL VOH VOL LPIN Parameter I/O supply voltage High-level input voltage Low-level input voltage Input pull-up voltage Input leakage current High-level output voltage Low-level output voltage Pin inductance Conditions Minimum 3.0 0.5 x VCCIO -0.5 0.7 x VCCIO Typical Maximum 3.6 VCCIO + 0.5 0.35 x VCCIO Units V V V V 0 < VIN < VCCIO IOUT = -500 A IOUT = 1,500 A -10 0.9 x VCCIO 10 A V 0.1 x VCCIO 15 V nH Table 32. GTL+ I/O Specifications Symbol VTT VREF VIH VIL VOL Note (10) Conditions Minimum 1.35 0.88 VREF + 0.1 VREF - 0.1 IOL = 34 mA 0.65 Parameter Termination voltage Reference voltage High-level input voltage Low-level input voltage Low-level output voltage Typical 1.5 1.0 Maximum 1.65 1.12 Units V V V V V 74 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Table 33. SSTL-2 Class I Specifications Symbol VCCIO VTT VREF VIH VIL VOH VOL Note (10) Conditions Minimum 2.375 VREF - 0.04 1.15 VREF + 0.18 -0.3 IOH = -7.6 mA IOL = 7.6 mA VTT + 0.57 VTT - 0.57 Parameter I/O supply voltage Termination voltage Reference voltage High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage Typical 2.5 VREF 1.25 Maximum 2.625 VREF + 0.04 1.35 3.0 VREF - 0.18 Units V V V V V V V Table 34. SSTL-2 Class II Specifications Symbol VCCIO VTT VREF VIH VIL VOH VOL Note (10) Conditions Minimum 2.3 VREF - 0.04 1.15 VREF + 0.18 -0.3 IOH = -15.2 mA IOL = 15.2 mA VTT + 0.76 VTT - 0.76 Parameter I/O supply voltage Termination voltage Reference voltage High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage Typical 2.5 VREF 1.25 Maximum 2.7 VREF + 0.04 1.35 VCCIO + 0.3 VREF - 0.18 Units V V V V V V V 13 Tools Table 35. SSTL-3 Class I Specifications Symbol VCCIO VTT VREF VIH VIL VOH VOL Note (10) Conditions Minimum 3.0 VREF - 0.05 1.3 VREF + 0.2 -0.3 IOH = -8 mA IOL = 8 mA VTT + 0.6 VTT - 0.6 Parameter I/O supply voltage Termination voltage Reference voltage High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage Typical 3.3 VREF 1.5 Maximum 3.6 VREF + 0.05 1.7 VCCIO + 0.3 VREF - 0.2 Units V V V V V V V Altera Corporation 75 Mercury Programmable Logic Device Family Data Sheet Table 36. SSTL-3 Class II Specifications Symbol VCCIO VTT VREF VIH VIL VOH VOL Note (10) Conditions Minimum 3.0 VREF - 0.05 1.3 VREF + 0.2 -0.3 IOH = -16 mA IOL = 16 mA VT T + 0.8 VTT - 0.8 Parameter I/O supply voltage Termination voltage Reference voltage High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage Typical 3.3 VREF 1.5 Maximum 3.6 VREF + 0.05 1.7 VCCIO + 0.3 VREF - 0.2 Units V V V V V V V Table 37. 3.3-V AGP -2X Specifications Symbol VCCIO VREF VIH VIL VOH VOL II Parameter I/O supply voltage Reference voltage High-level input voltage (12) Low-level input voltage (12) High-level output voltage Low-level output voltage Input pin leakage current Conditions Minimum 3.15 0.39 x VCCIO 0.5 x VCCIO Typical 3.3 Maximum 3.45 0.41 x VCCIO VCCIO + 0.5 0.3 x VCCIO Units V V V V V V A IOUT = -20 A IOUT = 20 A 0 < VI N < V CCIO 0.9 x VCCIO 3.6 0.1 x VCCIO 10 Table 38. 3.3-V AGP -1X Specifications Symbol VCCIO VIH VIL VOH VOL II Parameter I/O supply voltage High-level input voltage (12) Low-level input voltage (12) High-level output voltage Low-level output voltage Input pin leakage current Conditions Minimum 3.15 0.5 x VCCIO Typical 3.3 Maximum 3.45 VCCIO + 0.5 0.3 x VCCIO Units V V V V V A IOUT = -20 A IOUT = 20 A 0 < VI N < V CCIO 0.9 x VCCIO 3.6 0.1 x VCCIO 10 76 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Table 39. 1.5-V HSTL Class I Specifications Symbol VCCIO VREF VTT VIH (DC) VIL (DC) VIH (AC) VIL (AC) VOH VOL Note (10) Minimum 1.4 0.68 0.7 VREF + 0.1 -0.3 VREF + 0.2 VREF - 0.2 VREF - 0.1 Parameter I/O supply voltage Input reference voltage Termination voltage DC high-level input voltage DC low-level input voltage AC high-level input voltage AC low-level input voltage High-level output voltage Low-level output voltage Conditions Typical 1.5 0.75 0.75 Maximum 1.6 0.9 0.8 Units V V V V V V V V V IOH = 8 mA IOH = -8 mA VCCIO - 0.4 0.4 Table 40. 1.5-V HSTL Class II Specifications Symbol VCCIO VREF VTT VIH (DC) VIL (DC) VIH (AC) VIL (AC) VOH VOL Note (10) Minimum 1.4 0.68 0.7 VREF + 0.1 -0.3 VREF + 0.2 VREF - 0.2 VREF - 0.1 Parameter I/O supply voltage Input reference voltage Termination voltage DC high-level input voltage DC low-level input voltage AC high-level input voltage AC low-level input voltage High-level output voltage Low-level output voltage Conditions Typical 1.5 0.75 0.75 Maximum 1.6 0.9 0.8 Units V V V V V V V V V 13 Tools IOH = 16 mA IOH = -16 mA VCCIO - 0.4 0.4 Table 41. CTT I/O Specifications Symbol VCCIO VTT/VREF VIH VIL II VOH VOL IO Parameter I/O supply voltage Termination and input reference voltage High-level input voltage Low-level input voltage Input pin leakage current High-level output voltage Low-level output voltage Output leakage current (when output is high Z) Conditions Minimum 3.0 1.35 VREF + 0.2 Typical 3.3 1.5 Maximum 3.6 1.65 Units V V V VREF - 0.2 0 < VIN < V CCIO IOH = -8 mA IOL = 8 mA GND VOUT VCCIO VREF + 0.4 VREF - 0.4 10 10 V A V V A Altera Corporation 77 Mercury Programmable Logic Device Family Data Sheet Table 42. Bus Hold Parameters Parameter Conditions 1.8 V VCCIO Level 2.5 V 3.3 V A A 500 -500 A A Units Minimum Maximum Minimum Maximum Minimum Maximum Low sustaining current VIN > VIL (maximum) 30 -30 200 -200 50 -50 300 -300 70 -70 High sustaining VIN < VIH (minimum) current Low overdrive current High overdrive current 0 V < VIN < VCCIO 0 V < VIN < VCCIO Table 43. Mercury Device Capacitance Symbol CIO CCLK CRXHSDI CTXHSDI CCLKHSDI CFLEXLVDSRX CFLEXLVDSTX Note (13) Minimum Typical 13.5 16.9 8.0 18.0 7.5 13.4 13.4 Parameter I/O pin capacitance Input capacitance on CLK[4..1] pins Input capacitance on HSDI receiver pins Input capacitance on HSDI transmitter pins Input capacitance on HSDI clock pins Input capacitance on flexible LVDS receiver pins Input capacitance on flexible LVDS transmitter pins Maximum Unit pF pF pF pF pF pF pF 78 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Notes to Tables 20 - 43.: (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) See the Operating Requirements for Altera Devices Data Sheet. Minimum DC input is -0.5 V. During transitions, the inputs may undershoot to -0.5 V or overshoot to 4.1 V for input currents less than 100 mA and periods shorter than 20 ns. Maximum VCC rise time is 100 ms, and VCC must rise monotonically. VCCIO maximum and minimum conditions for LVPECL, LVDS, RapidIO, and 3.3-V PCML are shown in parentheses. All pins, including dedicated inputs, clock, I/O, and JTAG pins, may be driven before VCCINT and VCCIO are powered. Typical values are for TA = 25 C, VCCINT = 1.8 V, and VCCIO = 1.8 V, 2.5 V, and 3.3 V. These values are specified under the Mercury Device Recommended Operating Conditions shown in Table 3 on page 3. Input pins are grounded. In the test design, internal logic does not toggle. The test design does not use PLL or HSDI circuitry. All ESBs are in power-down mode. Pin pull-up resistance values will lower if an external source drives the pin higher than VCCIO. Drive strength is programmable according to values in Table 11 on page 53. For more information on termination, see AN 134: Using Programmable I/O Standards in Mercury Devices or AN 159: Using HSDI in Source-Synchronous Mode in Mercury Devices. VREF specifies the center point of the switching range. Capacitance is sample-tested only. Capacitance is measured using time-domain reflections (TDR). Measurement accuracy is within 5%. Timing Model The high-performance multi-level FastTrack Interconnect routing resources ensure predictable performance, accurate simulation, and accurate timing analysis. The predictable performance of Mercury devices offer an advantage over FPGAs, which use a segmented connection scheme and therefore have unpredictable performance. Figure 36 shows the timing model for bidirectional IOE pin timing. All registers are within the IOE. Figure 36. Synchronous Bidirectional Pin External Timing Model OE Register D PRN Q 13 Tools Dedicated Clock tXZBIDIR tZXBIDIR tOUTCOBIDIR CLRN Output Register D PRN Q Bidirectional Pin tINSUBIDIR tINHBIDIR CLRN Input Register PRN D Q CLRN Altera Corporation 79 Mercury Programmable Logic Device Family Data Sheet Tables 44 and 45 describe the Mercury device's external timing parameters. Table 44. Mercury External Timing Parameters Symbol tINSU tINH tOUTCO tINSUPLL tINHPLL tOUTCOPLL Notes (1), (2) Parameter Conditions Setup time with global clock at IOE register Hold time with global clock at IOE register Clock-to-output delay with global clock at IOE register Setup time with PLL clock at IOE input register Hold time with PLL clock at IOE input register Clock-to-output delay with PLL clock at IOE output register C1 = 35 pF C1 = 35 pF Table 45. Mercury External Bidirectional Timing Parameters Symbol tINSUBIDIR tINHBIDIR tOUTCOBIDIR tXZBIDIR tZXBIDIR tINSUBIDIRPLL tINHBIDIRPLL tOUTCOBIDIRPLL tXZBIDIRPLL tZXBIDIRPLL Notes (1), (2) Conditions Parameter Setup time for bidirectional pins with gobal clock at IOE input register Hold time for bidirectional pins with global clock at IOE input register Clock-to-output delay for bidirectional pins with global clock at IOE output register Synchronous IOE output enable register output buffer enable delay Setup time for bidirectional pins with PLL clock at IOE input register Hold time for bidirectional pins with PLL clock at IOE input register C1 = 35 pF Synchronous IOE output enable register to output buffer disable delay C1 = 35 pF C1 = 35 pF Clock-to-output delay for bidirectional pins with PLL clock at IOE output C1 = 35 pF register Synchronous IOE output enable register to output buffer disable delay C1 = 35 pF with PLL Synchronous IOE output enable register output buffer enable delay with PLL C1 = 35 pF Notes to Tables 44 and 45: (1) (2) These timing parameters are sample-tested only. All timing parameters are either to and/or from pins, including global clock pins. 80 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Tables 46 through 51 show external timing parameters for Mercury devices. Table 46. EP1M120 External Timing Parameters Symbol -5 Speed Grade Min tINSU tINH tOUTCO tINSUPLL tINHPLL tOUTCOPLL 0.67 0.00 2.00 0.59 0.00 0.50 2.08 3.30 Note (1) -6 Speed Grade -7 Speed Grade Min 0.73 0.00 3.32 2.00 0.62 0.00 2.08 0.50 2.15 3.49 Unit Max Min 0.70 0.00 2.00 0.64 0.00 0.50 Max Max ns ns ns ns ns ns Table 47. EP1M120 External Bidirectional Timing Parameters Symbol -5 Speed Grade Min tINSUBIDIR tINHBIDIR tOUTCOBIDIR tXZBIDIR tZXBIDIR (2) tZXBIDIR (3) tINSUBIDIRPLL tINHBIDIRPLL tOUTCOBIDIRPLL tXZBIDIRPLL tZXBIDIRPLL (2) tZXBIDIRPLL (3) 0.59 0.00 0.50 2.08 2.29 2.29 2.49 0.67 0.00 2.00 3.30 3.52 3.52 3.72 0.64 0.00 0.50 2.08 2.29 2.29 2.49 Note (1) -7 Speed Grade Min 0.73 0.00 3.32 3.53 3.53 3.73 0.62 0.00 0.50 2.15 2.39 2.39 2.64 2.00 3.49 3.74 3.74 3.99 -6 Speed Grade Min 0.70 0.00 2.00 Unit 13 Tools Max Max Max ns ns ns ns ns ns ns ns ns ns ns ns Altera Corporation 81 Mercury Programmable Logic Device Family Data Sheet Table 48. EP1M120 External Timing Parameters Symbol -7A Speed Grade Min tINSU tINH tOUTCO tINSUPLL tINHPLL tOUTCOPLL 0.74 0.00 2.00 0.62 0.00 0.50 2.15 3.50 Note (1) -8A Speed Grade Min 0.79 0.00 2.00 0.75 0.00 0.50 2.43 4.10 Unit Max Max ns ns ns ns ns ns Table 49. EP1M120 External Bidirectional Timing Parameters Symbol -7A Speed Grade Min tINSUBIDIR tINHBIDIR tOUTCOBIDIR tXZBIDIR tZXBIDIR (2) tZXBIDIR (3) tINSUBIDIRPLL tINHBIDIRPLL tOUTCOBIDIRPLL tXZBIDIRPLL tZXBIDIRPLL (2) tZXBIDIRPLL (3) 0.62 0.00 0.50 2.15 2.39 2.39 2.64 0.74 0.00 2.00 3.50 3.75 3.75 4.00 Note (1) -8A Speed Grade Min 0.79 0.00 2.00 4.10 4.30 4.30 4.58 0.75 0.00 0.50 2.43 2.67 2.67 2.95 Unit Max Max ns ns ns ns ns ns ns ns ns ns ns ns Table 50. EP1M350 External Timing Parameters Symbol -5 Speed Grade Min tINSU tINH tOUTCO tINSUPLL tINHPLL tOUTCOPLL 0.60 0.00 2.00 0.69 0.00 0.50 2.23 3.95 Note (1) -6 Speed Grade -7 Speed Grade Min 0.71 0.00 3.97 2.00 0.82 0.00 2.23 0.50 2.69 4.75 Unit Max Min 0.57 0.00 2.00 0.70 0.00 0.50 Max Max ns ns ns ns ns ns 82 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Table 51. EP1M350 External Bidirectional Timing Parameters Symbol -5 Speed Grade Min tINSUBIDIR tINHBIDIR tOUTCOBIDIR tXZBIDIR tZXBIDIR (2) tZXBIDIR (3) tINSUBIDIRPLL tINHBIDIRPLL tOUTCOBIDIRPLL tXZBIDIRPLL tZXBIDIRPLL (2) tZXBIDIRPLL (3) Notes to Tables 46 - 51: (1) (2) (3) Note (1) -7 Speed Grade Min 0.71 0.00 3.97 3.93 3.93 4.13 2.00 4.75 4.70 4.70 4.94 0.82 0.00 2.23 2.18 2.18 2.38 0.50 2.69 2.63 2.63 2.87 -6 Speed Grade Min 0.57 0.00 Unit Max Max Max ns ns ns ns ns ns ns ns ns ns ns ns 0.60 0.00 2.00 3.95 3.90 3.90 4.10 0.69 0.00 0.50 2.23 2.19 2.19 2.39 2.00 0.70 0.00 0.50 13 Tools Timing will vary by I/O pin placement. Therefore, use the Quartus II software to determine exact I/O timing for each pin. This parameter is measured with the Increase tZX Delay to Output Pin option set to Off. This parameter is measured with the Increase tZX Delay to Output Pin option set to On. Power Consumption Configuration & Operation Detailed power consumption information for Mercury devices will be released when available. The Mercury architecture supports several configuration schemes. This section summarizes the device operating modes and available device configuration schemes. Operating Modes The Mercury architecture uses SRAM configuration elements that require configuration data to be loaded each time the circuit powers up. The process of physically loading the SRAM data into the device is called configuration. During initialization, which occurs immediately after configuration, the device resets registers, enables I/O pins, and begins to operate as a logic device. The I/O pins are tri-stated during power-up and before and during configuration. Together, the configuration and initialization processes are called command mode; normal device operation is called user mode. Altera Corporation 83 Mercury Programmable Logic Device Family Data Sheet Before and during device configuration, all I/O pins are pulled to VCCIO by a built-in weak pull-up resistor. SRAM configuration elements allow Mercury devices to be reconfigured in-circuit by loading new configuration data into the device. Real-time reconfiguration is performed by forcing the device into command mode with a device pin, loading different configuration data, reinitializing the device, and resuming user-mode operation. In-field upgrades can be performed by distributing new configuration files. Configuration Schemes The configuration data for a Mercury device can be loaded with one of five configuration schemes (see Table 52), chosen on the basis of the target application. A configuration device, intelligent controller, or the JTAG port can be used to control the configuration of a Mercury device. When a configuration device is used, the system can configure automatically at system power-up. By connecting the configuration enable (nCE) and configuration enable output (nCEO) pins on each device, multiple Mercury devices can be configured in any of five configuration schemes. Table 52. Data Sources for Configuration Configuration Scheme Configuration device Passive serial (PS) Passive parallel asynchronous (PPA) Passive parallel synchronous (PPS) JTAG Configuration device MasterBlasterTM or ByteBlasterMVTM download cable or serial data source Parallel data source Parallel data source MasterBlaster or ByteBlasterMV download cable or a microprocessor with a Jam STAPL or JBC file Data Source f Device PinOuts For more information on configuration, see Application Note 116 (Configuring APEX 20K, FLEX 10K & FLEX 6000 Devices). See the Altera web site (http://www.altera.com) or the Altera Digital Library for pin-out information. 84 Altera Corporation Mercury Programmable Logic Device Family Data Sheet Revision History The information contained in the Mercury Programmable Logic Device Family Data Sheet version 2.2 supersedes information published in previous versions. Version 2.2 The following changes were made to the Mercury Programmable Logic Device Family Data Sheet version 2.2: Updated the condition values (symbols II and IOZ) in Table 22. Version 2.1 The following changes were made to the Mercury Programmable Logic Device Family Data Sheet version 2.1: Updated Table 8. Updated EP1M350 regular I/O banks in Table 13. Updated Note (6) in Table 14. 13 Tools Version 2.0 The following changes were made to the Mercury Programmable Logic Device Family Data Sheet version 2.0: Changed all references to PCML to 3.3-V PCML. Updated Table 4. Updated "High-Speed Differential Interface" on page 8. Added Tables 6 through 8. Added Figures 34 and 35. Updated I/O specifications in Tables 28 and 29. Updated Mercury device capacitance in Table 43. Updated EP1M120 device timing in Tables 46 through 49. Added EP1M350 device timing in Tables 50 and 51. Altera Corporation 85 Mercury Programmable Logic Device Family Data Sheet (R) 101 Innovation Drive San Jose, CA 95134 (408) 544-7000 http://www.altera.com Applications Hotline: (800) 800-EPLD Customer Marketing: (408) 544-7104 Literature Services: lit_req@altera.com Copyright (c) 2003 Altera Corporation. All rights reserved. Altera, The Programmable Solutions Company, the stylized Altera logo, specific device designations, and all other words and logos that are identified as trademarks and/or service marks are, unless noted otherwise, the trademarks and service marks of Altera Corporation in the U.S. and other countries. All other product or service names are the property of their respective holders. Altera products are protected under numerous U.S. and foreign patents and pending applications, mask work rights, and copyrights. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera Corporation. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. Altera Corporation 86 |
Price & Availability of EP1M350
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |